1997–2007
Verified catalog fitment for this exact Alfa Romeo generation. 17 printable parts currently match.
C3D–02237Adapter for installing the creator-linked LED fog lamp with the original fasteners on Alfa Romeo 156, 159 and Brera. The source instructs cutting the lamp tabs and securing the lamp with a zip tie in the printed groove. ABS is inferred for weather, vibration and lamp-area heat; PETG is an alternative. Confirm beam aim and legal compliance before road use.
Fits 156 · Tipo 932 · 159 · Tipo 939 · Brera · Tipo 939
C3D–02236Replacement loop insert for a broken Alfa Romeo 147/156 key fob, with both models explicitly identified by the creator. PETG is inferred for repeated key-ring flexing and impact; nylon is a tougher alternative.
Fits 147 · Tipo 937 · 156 · Tipo 932
C3D–02235Replacement sun-visor clip for Alfa Romeo 156. The creator specifically recommends ABS for longer service life; remove print supports before direct installation.
Fits 156 · Tipo 932
C3D–02234Two-piece drink holder designed and installed for a 1999 Alfa Romeo 156 2.0 Twin Spark. Bond the base and holder together, then attach the base with automotive-grade double-sided adhesive as the creator describes. PETG is inferred for cabin heat and toughness; ABS is an alternative.
Fits 156 · Tipo 932
C3D–02233Protective replacement cap for the Alfa Romeo 156 shock-absorber top. The creator only says it might fit Alfa 147 and GT, so those generations are withheld. ABS is inferred for exterior/under-bonnet heat, moisture and impact; PETG is an alternative.
Fits 156 · Tipo 932
C3D–02232Replacement CR2032 battery tray for an Alfa Romeo 156 key fob. The creator says it might fit other models, but those generations are withheld without corroboration. PETG is inferred for snap-fit toughness; PLA is an alternative for light use.
Fits 156 · Tipo 932
C3D–02231Simple winter cover that shields Alfa Romeo 156 windscreen-washer nozzles from snow. ABS is inferred for exterior cold, weather and sun exposure; PETG is an alternative.
Fits 156 · Tipo 932
C3D–02230Latest source revision of a clip-on paddle-shifter extension for Alfa Romeo 156 Selespeed controls. PETG is inferred for repeated handling and cabin heat; ABS is an alternative. Confirm secure retention and unobstructed steering-wheel movement before driving.
Fits 156 · Tipo 932
C3D–02229Replacement plastic nut for retaining the scuttle-panel cover. ABS is inferred for under-bonnet heat, weather and splash exposure; PETG is a lower-temperature alternative.
Fits 156 · Tipo 932
C3D–02228Multipart spacer set for installing a 6.5-inch front-door speaker without modifying the door. Print one base plate and two copies of the spacer, as the creator specifies. Explicitly designed for Alfa Romeo 147 and 156 doors. PETG is inferred for cabin heat resistance and screw-clamping toughness; ABS is an alternative.
Fits 147 · Tipo 937 · 156 · Tipo 932
C3D–02227Replacement retaining pin for the lower body panel of an Alfa Romeo 156. PETG is recommended here for vibration, impact and moisture resistance; ASA or ABS are alternatives for sustained exterior heat and weather exposure.
Fits 156 · Tipo 932
C3D–02226Replacement 50 mm center cap for alloy wheels using OEM 60652886. The source recommends printing solid PETG because its PLA retaining clips broke, and the photographed part accepts a separate 50 mm emblem. Confirm the wheel opening and original cap diameter before installation. The single-cap STL is supplied; the optional four-cap print plate and editable SketchUp source remain preserved in the audit archive.
Fits 145 / 146 · 145 / 146 (Tipo 930) · 147 · Tipo 937 · 156 · Tipo 932 +6
C3D–01898Two-part replacement sun-visor retaining clip. The creator recommends printing the base on its side for strength and using ABS because PLA may fail at cabin temperatures.
Fits 156 · Tipo 932
C3D–01896Replacement cover for the Bosch idle-control valve sensor used on the 156 and 166. The creator designed it because the original cover is discontinued separately from the complete sensor.
Fits 156 · Tipo 932 · 166 · Tipo 936
C3D–01875Replacement retaining pin designed by Mikael Tonialini for the luggage cover of a 156 Sportwagon. The creator recommends 100% infill and removing the central print support after printing.
Fits 156 · Tipo 932
C3D–01872Phone holder designed by Varsa for a 156 and mounted using a bicycle-style clamp.
Fits 156 · Tipo 932
Cup holder adapted by elec2rak to fit the side door panel of a 156, using the approximately 2 cm door-pocket gap. The creator specifies supports and 5% infill.
Fits 156 · Tipo 932