BMW vehicle line
Choose the precise generation for verified fitment, or browse all 15 parts currently associated with this vehicle line.
All generations
C3D–01298Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.
Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +1
C3D–01070Replacement stand-off spacer for fitting AUTOID rear carbon-fibre wheel-arch extensions to the BMW G42 M240i. The source is specific to that aftermarket arch kit and does not establish G87 fitment. Print in ASA, ABS, nylon, or another exterior-grade heat- and weather-resistant material, and verify the 12.4 mm diameter, 26.05 mm height, fastener engagement, arch alignment, and wheel/tyre clearance before road use.
Fits 2 Series · G42 / G87
C3D–01069Round organizer insert designed specifically for the factory cup holder in BMW F44 2 Series Gran Coupe models. It provides five coin slots, a BIC-lighter pocket, and an open storage compartment. The creator recommends PETG for cabin heat resistance; verify the approximately 80.4 mm outside diameter against the vehicle before printing.
Fits 2 Series · F44 Gran Coupe
C3D–01068Short adapter ring that centers narrow energy-drink cans in the factory cup holder of BMW F45 Active Tourer and F46 Gran Tourer models. The creator physically tested the reduced-height ring and photographed it installed.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01067Flexible replacement for BMW rubber buffer 51466967605, creator-tested on an i3 and catalogued for F45, E81/E87, F20/F21, I01, and X1 E84. Print in approximately 85A TPU and cut out the temporary support tab after printing. Within the combined E8x generation, documented fitment is E81/E87 only.
Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 2 Series · F45 / F46 Active / Gran Tourer +2
C3D–01066Organizer tray for the compartment beneath the armrest in right-hand-drive BMW F45 Active Tourer and F46 Gran Tourer models. The source photograph shows the printed tray installed; this fitment is RHD-specific.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01065Four support-free mounting-base variants that clip into the small center-console storage pocket of BMW F45/F46 models. Includes fixed and rotating plates; rotating versions use an M5 nut and 12–20 mm bolt. Use PETG, ASA, or ABS rather than ordinary PLA.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01064Replacement hook that retains the cargo cover in position on the BMW F45 2 Series Active Tourer. Creator photographs show the physical hook installed; compare mounting orientation and clearances before fitting.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01063Replacement linkage between the rear center-console vent thumbwheel and airflow flap on BMW F45/F46 Active Tourer and Gran Tourer, including pre-LCI and LCI. Remove the vent assembly for access, verify linkage orientation, and use a cabin-heat-resistant material.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01062Cup-holder extension designed and physically installed in a BMW F22 2 Series to move large 32-ounce cups clear of the dashboard while retaining the original recess as small-item storage. Plain and roundel variants are included. The creator reports good retention with a small shim and uses heat-resistant PETG-CF. Verify fit, cup stability, and clearance from controls before driving.
Fits 2 Series · F22 / F23 / F87
C3D–01061Cup-holder insert for 250 ml beverage cans in BMW F22 and F87 interiors. The creator uses the matching design in an F87 M2 and provides installed physical views. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.
Fits 2 Series · F22 / F23 / F87
C3D–01060Cup-holder insert for 330 ml beverage cans in BMW F22 and F87 interiors. The creator uses it in an F87 M2 and shows both the empty insert and a can seated in it. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.
Fits 2 Series · F22 / F23 / F87