3 Series E30

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Replacement release handle for E30 Touring luggage-compartment side covers, physically installed and reported working with the original bent linkage rods. Verify both latches release and re-engage.

Fits 3 Series · E30

Screw-on protective cover for exposed E30 front wheel-bearing spindle surfaces during restoration, washing, blasting, painting or storage. It is physically shown on the spindle and is removed before wheel-bearing assembly.

Fits 3 Series · E30

Replacement clip retaining the bulb holder in early E30 taillights, printed in PETG and physically installed. Late-light fitment is unconfirmed. The creator-listed 63211376879 resolves to an unrelated rotary knob in BMWFans, so it is intentionally omitted.

Fits 3 Series · E30

Replacement latch striker for E30 Touring luggage-compartment side covers, reproduced from the original and physically shown working. BMWFans confirms latch striker 51471947370.

Fits 3 Series · E30

Replacement front-seat rail nut cap for E30 cars built before September 1985, copied from the original and physically compared. BMWFans confirms covering cap 52101913670.

Fits 3 Series · E30

Click-fit cosmetic cap designed around the E30 wheel-lock bolt and physically fitted. The creator-listed 36131182006 identifies a complete lock set, not the printed cap, so no OEM number is assigned. Verify the cap cannot loosen near the wheel.

Fits 3 Series · E30

Replacement bracing cover for early-model E30 fog lamps, reproduced from the original and physically compared after a fit-improving revision. BMWFans confirms cover 63171373577.

Fits 3 Series · E30

Bond-on repair for a broken outer lock section on E30 Touring luggage-compartment side panels, physically demonstrated on an iX panel and mirrorable for either outer side. The referenced latch and spring are separate components and are not assigned.

Fits 3 Series · E30

Replacement front engine wiring holder for E30 M20 and creator-listed E28/E34 applications, physically compared with the original. BMWFans confirms holder 11141716134. Use ASA, ABS or another engine-bay-rated material and inspect for heat distortion.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement slotted screw for retaining E30 seat-mechanism covers. The creator printed and tested revision 3.1 with a deeper screwdriver slot. Tighten only enough to retain the trim.

Fits 3 Series · E30

Five-file replacement centre-cap system for factory-style 14-inch E30 basket-weave wheels, using a face, locking clip and choice of three hex inserts. The source shows physical installation; test one assembly and verify positive retention before road use.

Fits 3 Series · E30

Smooth replacement covers for the MOMO K2006 steering-wheel hub and the separately measured Alpina leather hub, physically printed and fitted on E30. Select the correct file and verify steering-column clearance.

Fits 3 Series · E30

Resin-printable replacement pivot for the E30 convertible top-lock centering mechanism, physically compared with the original. BMWFans identifies the component as covering for centering bolt 54311971255. Verify pivot movement and roof latching before driving.

Fits 3 Series · E30

Plain replacement cover designed for the sunroof motor opening of a 1987 BMW E30 325is and shown physically fitted. Use heat-resistant cabin material and verify screw and headliner clearance.

Fits 3 Series · E30

Replacement adjustment knob for BMW E30 M-Sport seats, physically shown as a finished print. Match the seat shaft and verify secure engagement before use.

Fits 3 Series · E30

Left and right repair tabs for cracked E30 instrument-cluster mounting ears, test-fitted against an intact cluster and documented for screw or adhesive installation. Align the tabs in the dash before removing the damaged originals.

Fits 3 Series · E30

Replacement plastic grommet used at E30 grille and rear license-plate mounting points, physically compared with the original. The creator also lists E36, E46, E90 and E92 applications; BMWFans confirms grommet 51131840154.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +1

Replacement cap for E30 front seat-belt anchorage bolts, copied from the original and physically fitted on stock, sport and Recaro seats. BMWFans confirms covering cap 72111808464. Do not disturb or conceal a loose anchorage bolt.

Fits 3 Series · E30

Straight and 90-degree two-piece shells for repairing disintegrated 2.5 mm watertight terminals on BMW E30, E36 and E46. The source shows completed physical connectors. Bond with suitable RTV and verify terminal lock, polarity, insulation and sealing.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46

Replacement fastener for E30 front-seat side covers, copied from the original and physically compared. It supports stock, sport and Recaro seats; BMWFans confirms push-button 52101906933.

Fits 3 Series · E30

Replacement cap for the E30 luggage-compartment jack mount, copied from the original and physically installed. BMWFans confirms cover 51711916269.

Fits 3 Series · E30

Replacement side covers for BMW Reverse RDS, non-RDS, Bavaria and Business radios used in E30, E32, E34 and E36. The source shows physical fit and finish; BMWFans confirms covering cap 65126907823.

Fits 3 Series · E30 · 3 Series · E36 · 5 Series · E34 +1

Replacement front-strut top dust cover for E30 cars fitted with Koni adjustable dampers where the stock cover does not fit. The creator printed and used the PETG version; confirm adjuster clearance and cap retention.

Fits 3 Series · E30