Z3

Replacement beauty cap for M50, M52 and M54 engine-cover fasteners, physically shown on the engine. BMWFans identifies the exact component as cap 11121726089 and confirms E34, E36, E38, E39, E46, E53, E60/E61, E65/E66, E83, E85 and Z3 applications. Use engine-bay-rated material and keep it clear of hot or moving parts.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E34 +8

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E30 · 3 Series · E36 +14

Replacement housing for the seat-drive mechanism used in both Roadster and Coupe. The creator reports the ABS version has worked for seven years and recommends nylon; STEP geometry is included. Seat removal is required, so isolate the battery, observe restraint-system precautions, and verify travel, locking and fastener torque before driving.

Fits Z3 · E36/7 / E36/8

Removable armrest shown physically installed over the centre console. Confirm handbrake, shifter, belt-buckle and seat-travel clearance and remove it if it can interfere with any control.

Fits Z3 · E36/7 / E36/8

Flexible replacement retaining lanyard for a broken or missing fuel cap tether in the creator's 2002 car, shown installed. No separately serviced BMW number was established for the printed tether. Confirm the cap seals and the lanyard cannot foul the filler neck or flap.

Fits Z3 · E36/7 / E36/8

Caliper-modeled replacement for deteriorated floor plugs in the creator's 1998 car, shown installed and compared with the original. The TPU print was accidentally rain-tested and reported watertight. Inspect the surrounding metal, use compatible sealant only if required, and verify water sealing.

Fits Z3 · E36/7 / E36/8

Exact-copy replacement for the upper glovebox latch catch, shown installed. RealOEM and BMWFans identify the separately serviced upper catch as 51161849472 and show it in the glovebox diagram for this generation. Verify the lid latches, releases and sits flush without excessive force.

Fits Z3 · E36/7 / E36/8

Screw-retained sleeve for a broken lower finger on the passenger-seat belt guide in the creator's 2002 car. The installed repair, original damage and break diagrams are documented. It does not replace the belt or anchor; verify smooth belt feed and retraction before driving.

Fits Z3 · E36/7 / E36/8

Custom blank for routing microphone or charging cable through an unused centre-console button opening in the creator's 2002 car, shown installed. Secure and fuse powered wiring, protect cable edges, and keep controls unobstructed.

Fits Z3 · E36/7 / E36/8

Replacement right-side dashboard vent designed to snap into the original opening and reported as an effortless installation. It is the passenger-side vent on LHD cars and driver-side vent on RHD cars. BMWFans identifies the right defroster-nozzle cover as 64228399954 from September 1995. Verify louvre movement, duct sealing and dashboard retention.

Fits Z3 · E36/7 / E36/8

Longer repair guide for the Roadster and M Roadster seatbelt guide, independently remeasured after a shorter design moved in use. The creator reports successful PETG use and shows it installed. This is a trim guide, not a restraint anchor; confirm the belt feeds and retracts freely and never modify the belt or anchor.

Fits Z3 · E36/7 / E36/8

Two-piece cupholder and mounting insert for the rear-console slot behind the handbrake in the creator's 1999 2.5-litre Roadster. The source shows it installed. Bond or fasten the parts securely and confirm handbrake, seat and belt-buckle clearance.

Fits Z3 · E36/7 / E36/8