car3dparts.

Jeep vehicle line

CJ

Choose the precise generation for verified fitment, or browse all 26 parts currently associated with this vehicle line.

All generations

CJ parts

Open filtered catalog →
Taillight Housing and SeparatorC3D–00711
JeepExterior lighting, cameras & sensors

Taillight Housing and Separator

Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Heater-Control Cable End ClipC3D–00701
JeepDashboard & controls

Heater-Control Cable End Clip

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Fits Cherokee / Liberty · XJ · CJ · CJ-5 · CJ · CJ-7 +2

Paddle-Door HandlesC3D–00719
JeepInterior doors & windows

Paddle-Door Handles

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Fits CJ · CJ-7 · Wrangler · YJ · Wrangler · TJ

Taillight LensC3D–00713
JeepExterior lighting, cameras & sensors

Taillight Lens

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Windshield-Bracket CupholderC3D–00725
JeepBody panels & exterior trim

Windshield-Bracket Cupholder

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Floor Drain PlugC3D–00704
JeepBody panels & exterior trim

Floor Drain Plug

Snap-in plug for a flat one-inch floor drain hole. The source warns that a hole crossing a floor bend may need a slightly smaller plug.

Fits CJ · CJ-2A · CJ · CJ-3A · CJ · CJ-3B +5

Factory-Style Windshield Hood BlocksC3D–00991
JeepDoors, bonnet, boot & bed hardware

Factory-Style Windshield Hood Blocks

Three factory-style windshield hood-block geometries measured from original parts and Willys master-parts documentation. Separate printable blocks cover CJ-2A, CJ-3A, and CJ-3B vehicles; two matching blocks are required per Jeep.

Fits CJ · CJ-2A · CJ · CJ-3A · CJ · CJ-3B

Taillight-Lens GasketC3D–00712
JeepExterior lighting, cameras & sensors

Taillight-Lens Gasket

Flexible gasket that seals between the rectangular taillight housing and lens. The source specifies TPU and the mounting pattern is documented across late CJ, YJ and TJ applications.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +2

Speedometer Bulb DiffuserC3D–01003
JeepExterior lighting, cameras & sensors

Speedometer Bulb Diffuser

Replacement translucent cover for the illumination bulbs inside a Jeep CJ-7 speedometer assembly. It reproduces the small heat-damaged factory diffuser and the source documents the corresponding CJ dashboard.

Fits CJ · CJ-7