car3dparts.

Jeep vehicle line

Gladiator

Choose the precise generation for verified fitment, or browse all 23 parts currently associated with this vehicle line.

Fitment

Generations

All generations

Gladiator parts

Open filtered catalog →
Magnetic Tazer JL Mini MountC3D–00822
JeepDashboard & controls

Magnetic Tazer JL Mini Mount

Tool-free magnetic holder for a Tazer JL Mini module under the dashboard of Wrangler JL or Gladiator JT models. It uses five 12 by 3 mm magnets and leaves the status light and USB port accessible.

Fits Gladiator · JT · Wrangler · JL

Trail-Rail Spring CleatC3D–00973
JeepCabin trim, cargo & roof

Trail-Rail Spring Cleat

Two-piece spring-loaded cargo cleat for the Gladiator JT Trail Rail system. The body indexes into the rail grooves and uses an M8 T-nut, threaded insert, and compression spring documented by the creator.

Fits Gladiator · JT

Six-Switch Media-Center PanelC3D–00986
JeepDashboard & controls

Six-Switch Media-Center Panel

Two-piece six-switch panel that replaces the right-side media-center trim in Wrangler JL and Gladiator JT dashboards. The rear plate and switch retaining nuts clamp the assembly around the factory opening.

Fits Gladiator · JT · Wrangler · JL

Yaesu FTM-500 Control-Head MountC3D–00985
JeepDashboard & controls

Yaesu FTM-500 Control-Head Mount

Two-piece dashboard-pocket mount for a Yaesu FTM-500 control head in Wrangler JL and Gladiator JT vehicles. It requires no vehicle drilling and the source documents the installed assembly from three angles.

Fits Gladiator · JT · Wrangler · JL

Compact JL/JT Key-Fob HousingC3D–00984
JeepCabin trim, cargo & roof

Compact JL/JT Key-Fob Housing

Compact replacement housing for Wrangler JL and Gladiator JT key-fob electronics, factory buttons, battery, and screws. The selected revision-four top and bottom incorporate the creator's fit and stiffness updates.

Fits Gladiator · JT · Wrangler · JL

Bed Switch-and-Power-Socket PanelC3D–00983
JeepDoors, bonnet, boot & bed hardware

Bed Switch-and-Power-Socket Panel

Replacement panel for the Gladiator JT bed opening with provisions for one accessory switch and one twelve-volt socket. It fastens to four M4 rivet nuts and the source shows both the factory opening and completed installation.

Fits Gladiator · JT

Auxiliary-Battery Lead InsulatorC3D–00982
JeepEngine-bay electrical & sensors

Auxiliary-Battery Lead Insulator

Flexible insulating boot for the disconnected cable end left by a non-invasive Gladiator JT auxiliary-battery delete. The source documents the installed cover after towing use and recommends securing its neck with tape.

Fits Gladiator · JT

Key-Fob Alarm-Button GuardC3D–00981
JeepCabin trim, cargo & roof

Key-Fob Alarm-Button Guard

Two-piece protective shell for Wrangler JL and Gladiator JT key fobs. The bolted enclosure shields the panic button from accidental pocket presses while retaining access to the normal controls.

Fits Gladiator · JT · Wrangler · JL

Roll-Up Tonneau-Cover BracketsC3D–00980
JeepDoors, bonnet, boot & bed hardware

Roll-Up Tonneau-Cover Brackets

Left and right replacement brackets for the Mopar roll-up tonneau cover on 2020-and-newer Gladiator JT beds. Each bracket accepts two M5 threaded inserts; the creator reports that the pair fits and works.

Fits Gladiator · JT

Flexible Window Armrest ExtenderC3D–00979
JeepInterior doors & windows

Flexible Window Armrest Extender

Soft slip-on window-sill armrest for a Gladiator JT door card. The flexible pad remains in place while the door and window operate, and its low profile is documented in installed and uninstalled physical views.

Fits Gladiator · JT

Bed-Outlet Wiring SpacersC3D–00978
JeepDoors, bonnet, boot & bed hardware

Bed-Outlet Wiring Spacers

Two- and three-gland spacers for routing additional wiring through the Gladiator JT factory bed-outlet opening. The source documents the required longer fasteners, edge protection, gasket, and heat-resistant material.

Fits Gladiator · JT