Defender Td5

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Two headlining fastener sizes for a 110.

Fits Defender · Td5

Replacement latch insert for the truck-cab rear sliding window, designed to reuse the original latch housing.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Clip-in dashboard-vent deflector that directs part of the demister airflow towards the side window. The creator positions it over the vent funnel, about 150 mm from the outer end.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Fits Defender · Td5

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Adaptor to fit Discovery 2 Cruise Control switch to Defender td5. Quote from SimonRafferty: "It's very easy to add cruise control to any Td5 Land Rover Defender just by adding a couple of wires to the ECU and connecting them to a switch. (search on line for details) Unfortunately, there are no nice looking switches. My solution was to fit a switch from a Td5 Discovery 2 - and print this adaptor so it can easily screw on to the steering column. This is version 2 which is a much better fit and prints in one piece. Use higher temperature filament such as PETG or PAHT - otherwise it will melt in the sun. That's how come V2 came to be! Insert a couple of M4 Nuts into the slots provided, then attach the switch with 2 x M4 x 10mm screws"

Fits Defender · Td5

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Fits Defender · Td5

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Workshop fitting tool for seating the rear hub seal squarely.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Bracket for mounting a 2016 Elinz FHD dashcam at the passenger sun-visor fixing point, reusing the original visor screw.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Four-piece replacement repair set for the air-conditioning louvre assembly in a 1995 Land Rover Defender 300 Tdi (1994-1998), comprising the louvre, outer frame, alignment strip, and louvre clip rail. The louvre-fit holes require drilling to 2.5 mm; the louvre requires supports and the other components print without supports. Verify the exact AC vent variant, hole size, retention, louvre movement, and cabin-heat material suitability before installation. This should also fit other pre-puma/td4 Defenders

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement blanking plate for unused dashboard switch openings in the Land Rover Defender TD5 (1998-2005). It fills a dashboard opening where a switch is not fitted. Verify the exact dashboard aperture, dimensions, retention, and clearance before installation. PETG is the specified printing material; support is specified for printing.

Fits Defender · Td5

Full-size upper dashboard panel for the Land Rover Defender Td5 (1998–2005), replacing the upper dashboard top/facia component across the instrument-panel area. Verify VIN and windscreen/vent variant, drive side, demister and fastener interfaces, dimensions, clearances, and material/print strength before installation.

Fits Defender · Td5

Drop-in ashtray-delete dash mount base for the Land Rover Defender Td5 (1998-2005). It replaces the factory top-dash ashtray with a flat, level surface for adhesive or non-slip mounting of a display, GPS, dashcam, or similar accessory, and includes a cable-routing opening. No drilling or permanent dashboard modification is required; verify the dashboard opening, device footprint, clearances, cable path, and printed-part strength before installation.

Fits Defender · Td5

Cubby-box dock for a cased Samsung Galaxy S5 and a cylindrical Qi charging puck.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two replacements for the unused 1998 centre-panel opening: a plain plug and a post-mounted version for a small air freshener.

Fits Defender · 300 Tdi · Defender · Td5

Replacement interior end cap for the roof reinforcement bar.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Modular dashboard panel for three rectangular switches, supplied as a one-piece version and a split panel with end cap.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Bezel for installing a 30 mm USB charging outlet in the unused position beside the rear-wiper control on the centre console. The USB outlet clamps the bezel in place.

Fits Defender · Td5