Series 3

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +8

Three-part replacement socket assembly for an indicator or position lamp using a separate single-contact bulb holder. Verify the 33 mm housing fit, wiring, insulation, and weather sealing.

Fits Series · 1 · Series · 2 · Series · 2A +1

Its an alternative to the front grille screw plastic mounts.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Replacement UP–DOWN heater airflow control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Fits Series · 2 · Series · 2A · Series · 3

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Replacement lettered knob for a missing bulkhead-vent control. It is designed to be heat-pressed onto the original mechanism

Fits Series · 3

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Fits Series · 3

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3

Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.

Fits Series · 2A · Series · 3

Replacement support bracket for the instrument cluster where the original is missing or damaged. Compare handedness, hole spacing, and dashboard structure before printing.

Fits Series · 3

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.

Fits Series · 3

Workshop mandrel for centring the clutch plate during assembly. Confirm the spigot and spline diameters against the gearbox input shaft and clutch before use.

Fits Series · 2 · Series · 2A · Series · 3

Left- and right-hand enclosures for 100 mm speakers up to approximately 48 mm deep. Mirrored and split-file variants are included

Fits Series · 3

Slightly oversized 16 mm bonnet-hinge bush intended to reduce movement and rattling in worn hinge carriers. Print with strong layer bonding and high infill

Fits Series · 3

Replacement COLD–WARM heater control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Fits Series · 2 · Series · 2A · Series · 3

Modular dashboard base with two M6 attachment points, plus compatible Garmin and Motorola device holders. The base attaches to the vinyl dashboard with automotive-grade double-sided tape.

Fits Series · 3

Replacement lower-dashboard air vent in the later flat style.

Fits Series · 3

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Fits Series · 3

Replacement bush used with a standard 5/16-inch bolt and locking nut to align the brake shoes. Tap the printed bore to suit the bolt thread and follow the source adjustment method.

Fits Series · 1 · Series · 2 · Series · 2A +1