car3dparts.

Mercedes vehicle line

190 Series

Choose the precise generation for verified fitment, or browse all 20 parts currently associated with this vehicle line.

Fitment

Generations

All generations

190 Series parts

Open filtered catalog →
Mirror-Adjustment HandleC3D–01573
MercedesMirrors

Mirror-Adjustment Handle

Two-piece handle and lock for the 5 mm manual driver-side mirror adjustment rod. The creator explicitly states W123, W124, W201 and W126 fitment. Use tough cabin material, check the rod diameter and locking engagement, and confirm full mirror travel without forcing the cable or mechanism.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124 · S-Class · W126 / C126 +1

Sun-Visor Retaining ClipC3D–01568
MercedesCabin trim, cargo & roof

Sun-Visor Retaining Clip

Two-piece retaining clip and screw cover for the cabin sun visor. The creator made it for a 1989 300E and explicitly states W123, W124, W126, W140 and W201 fitment, while noting that it does not carry electrical contacts for illuminated vanity mirrors. Print the main clip and locking cover in the documented orientations, use cabin-heat-resistant material, compare the screw position and visor profile, and confirm secure retention and free release before driving.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124 · S-Class · W126 / C126 +2

Double-DIN Radio Adapter FrameC3D–01612
MercedesDashboard & controls

Double-DIN Radio Adapter Frame

Custom adapter frame for the specific 7-inch double-DIN Android head unit linked by the creator. Source photographs show the printed frame and the modified centre-console opening. Confirm the radio dimensions and console cut-out before printing, protect the veneer and wiring, provide adequate ventilation and strain relief, and do not assume other double-DIN units share the same bezel geometry.

Fits 190 Series · W201

Front-Right Sill-End CapC3D–01621
MercedesBody panels & exterior trim

Front-Right Sill-End Cap

Replacement cover for the front-right opening in the side-member/sill cladding. Source photographs show the installed location, the original and printed pieces, and the CAD model. EPC evidence identifies the right-front covering; use UV-, weather- and impact-resistant material, inspect the mounting opening for corrosion, and confirm the cap remains secure.

Fits 190 Series · W201

Centre-Console Attachment BracketC3D–01618
MercedesConsole & storage

Centre-Console Attachment Bracket

Replacement angle bracket connecting the centre-console panel to the transmission-tunnel covering on earlier cars. The creator copied the broken original, identifies EPC position 44, and states that the original threaded insert and screw are reused. Confirm early-model console geometry, use tough cabin-heat-resistant material, and tighten only enough to retain the trim without cracking the bracket.

Fits 190 Series · W201

Tow-Eye Cover Retaining ClipC3D–01615
MercedesBumpers, grilles & guards

Tow-Eye Cover Retaining Clip

Retaining clip with a safety tab for one side of the front towing-eye cover; the creator instructs mirroring the model for the opposite side. Only CAD/source screenshots are available, so compare the original cover and clip geometry carefully. Use UV-, weather- and impact-resistant material and confirm the cover remains retained at road speed.

Fits 190 Series · W201

Switch-Blanking CoverC3D–01610
MercedesDashboard & controls

Switch-Blanking Cover

Blanking cover for an unused rectangular switch opening in the upper centre dashboard trim. The creator designed and physically fitted it in a 190-series cabin but does not claim other applications. Compare the opening and surrounding veneer before printing, use cabin-heat-resistant material, and verify the cover cannot interfere with the adjacent rear-window-demister switch or air vent.

Fits 190 Series · W201

Centre-Console Switch-Panel SupportC3D–01625
MercedesConsole & storage

Centre-Console Switch-Panel Support

Replacement plastic support panel beneath the wooden centre-console switch trim. The creator reports that the design works but may require sanding. Compare the switch layout and console version before printing, use cabin-heat-resistant material, deburr all openings, and confirm switches, wiring and the selector remain unobstructed.

Fits 190 Series · W201

Blower-Control Switch CapC3D–01619
MercedesDashboard & controls

Blower-Control Switch Cap

Replacement cap for a broken cabin-blower control switch, modeled from the original for a 190-series interior. The source provides comparison imagery but no long-term validation details. Compare the switch shaft and detents, use tough cabin-heat-resistant material, and verify every blower position operates and the cap cannot bind against the panel.

Fits 190 Series · W201

Wiper-Linkage Drive GearC3D–01613
MercedesWipers & washers

Wiper-Linkage Drive Gear

Replacement gear for the single-arm windscreen-wiper mechanism. The creator documents the dismantled mechanism, press-fitting the gear after heating the splined shaft, and specifies nylon at 100% infill. Treat this as a mechanism repair: compare tooth count and shaft profile, preserve alignment and lubrication, and bench-test full travel, parking and stall behavior before wet-road use.

Fits 190 Series · W201

Bonnet-Release HandleC3D–01622
MercedesDoors, bonnet, boot & bed hardware

Bonnet-Release Handle

Replacement handle modeled after the original bonnet-release handle. Source photographs document the latch area and installed handle location. Compare the pivot and cable-end geometry, use tough cabin-heat-resistant material, preserve full cable travel, and verify the bonnet opens, closes and latches correctly before driving.

Fits 190 Series · W201

Driver-Vent SurroundC3D–01620
MercedesDashboard & controls

Driver-Vent Surround

Replacement driver-side dashboard vent surround, supplied as both a complete model and a two-piece version for easier printing. The creator reports that it fitted but was not fully refined, warns that PLA deformed in summer heat, and says to mirror the part for left-hand-drive use. The complete STL appears about 25.4 times smaller than the split files when interpreted as millimetres, so verify source units and final dimensions in the slicer. Confirm steering side and vent geometry, print in heat-resistant material, and verify free vent-slider movement.

Fits 190 Series · W201