car3dparts.

Mercedes vehicle line

A-Class

Choose the precise generation for verified fitment, or browse all 18 parts currently associated with this vehicle line.

All generations

A-Class parts

Open filtered catalog →
Parcel Shelf Hinge PairC3D–01860
MercedesCabin trim, cargo & roof

Parcel Shelf Hinge Pair

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

Fits A-Class · W177

Manual Seat-Slide Adjustment HandlesC3D–01777
MercedesSeats & restraints

Manual Seat-Slide Adjustment Handles

Direct-replacement manual seat adjustment handles supplied as separate left- and right-hand files. The creator designed them for a 2007 vehicle and identifies the right-hand component as original part A1699190661; Mercedes genuine-parts and PartSouq listings corroborate that number as the right-side seat-adjustment lever. The OEM number applies to the right-hand file only. Use a tough, heat-resistant material, compare the mounting socket and travel with an intact handle, and verify that the seat locks positively in every tested position before driving.

Fits A-Class · W169

Display-Side Phone HolderC3D–01826
MercedesDashboard & controls

Display-Side Phone Holder

Phone holder designed to fit beside the dashboard display. The author supplies a base holder and phone-specific variants for iPhone 11, iPhone 8 Plus, and the 2016 iPhone SE, and shows a physical holder fitted in the vehicle. The creator used heat-resistant Extrudr GreenTEC rather than ordinary PLA, which can soften in a hot cabin. Choose only the matching variant, confirm secure retention, and keep the device clear of the driver’s view, controls, airbags, and ventilation.

Fits A-Class · W176

Center-Console Phone HolderC3D–01829
MercedesConsole & storage

Center-Console Phone Holder

Two alternative phone-holder files designed to sit in the middle-console compartment for A180 and A200 variants. The creator states compatibility with iPhone and Android devices, simple installation, and support-free printing; source photos show the holder installed with a phone and charging cable. Choose one alternative file, verify a stable fit with the specific phone and case, use a cabin-heat-resistant material, and keep the device and cable clear of the selector and other controls.

Fits A-Class · W176

Floor-Mat Retaining Clip SetC3D–01776
MercedesCabin trim, cargo & roof

Floor-Mat Retaining Clip Set

Two-piece retaining clip for the driver's floor mat. The creator designed and tested it on a 2011 vehicle, states that the two halves permanently snap together through the mat, and notes that removal from the floor takes slightly more force than the original. The source print used PLA with a 0.4 mm nozzle, no raft and no supports; for sustained cabin heat, prefer an automotive-temperature-capable material. Confirm that both halves are fully locked, that the mat cannot slide toward the pedals, and stop using the print if it loosens or cracks.

Fits A-Class · W169

Power-Window Switch Hinge PairC3D–01780
MercedesDashboard & controls

Power-Window Switch Hinge Pair

Replacement hinge inserts for the power-window actuator switches, supplied as distinct driver- and passenger-side files because the locating pins are different sizes. The creator shows the printed parts with the original switch housing and secures each insert with double-sided tape on its back and bottom surfaces. Use a heat-resistant material, select the correct side, keep adhesive clear of contacts and moving surfaces, and confirm normal switch return and window operation before refitting the door controls.

Fits A-Class · W169

Front Door-Trim Retaining ClipC3D–01779
MercedesInterior doors & windows

Front Door-Trim Retaining Clip

Replacement retaining clip/cover for the front door trim panel. The creator explicitly identifies both the A-Class application and exact child-component number A1697270014; independent genuine-parts listings corroborate it as the left/right front door-card trim clip also used on the B-Class W245, which is absent from the live taxonomy. Verify trim colour and socket geometry against the removed clip, press the panel home without forcing it, and replace the print if the panel is not held securely.

Fits A-Class · W169

Twin-Vent Phone-Mount AdapterC3D–01825
MercedesDashboard & controls

Twin-Vent Phone-Mount Adapter

Phone-mount adapter designed for the two center dashboard vents and used by the creator with a uGreen magnetic mount. The source identifies exact hatchback fitment and provides the printable adapter; the mating phone mount is not included. Print in ABS as specified by the creator, verify that the adapter does not crack or loosen, maintain airflow, and position the phone so it cannot obstruct the road view, controls, display, or airbags. The source GNU GPL v2 licence is represented by the API’s other licence value.

Fits A-Class · W176

Glovebox Pen-Holder ClipC3D–01727
MercedesDashboard & controls

Glovebox Pen-Holder Clip

Strengthened replacement clip for the glovebox ballpoint-pen holder. The creator explicitly lists W169, W203, W204, W209, W212 and W245 fitment, shows the part installed and recommends ABS for cabin heat; W245 is absent from the live taxonomy. No body, market or production-break split is stated, so compare the original clip and glovebox recess before printing, fit without damaging the lid and confirm the pen and clip cannot detach into the footwell.

Fits A-Class · W169 · C-Class · W203 / S203 / CL203 · C-Class · W204 / S204 / C204 +2

Center Console OrganizerC3D–01859
MercedesConsole & storage

Center Console Organizer

Three-piece organizer and lid system for the center-console storage compartment. The preserved author package names the main organizer and lid geometry for W177, and four author photographs show the parts installed and in use. No screws or bolts are required; the creator states that the hooks lock into place with light force. Use a cabin-heat-resistant material, test the hook engagement gradually, and verify that the lid and armrest open and close freely without pinching stored items or wiring.

Fits A-Class · W177

Wireless Charger DockC3D–01858
MercedesConsole & storage

Wireless Charger Dock

Drop-in holder for a MagSafe-compatible wireless charger in the front storage cubby. The creator made and photographed it in a 2020 car and explicitly states W177 fitment. They also suggest same-generation W247, C118, H247 and X247 compatibility but require a visual cubby check; those lines are not among the live generations in this catalog, so only the tested W177 generation is linked. The model is sized around the charger identified on the source page and was designed for an S23 Ultra; verify phone, case, charger and cable clearance before printing. Place the largest face down and use supports. The creator recommends a cabin-heat-resistant material such as PET, PETG, ABS or ASA. Secure the cable and confirm the dock cannot obstruct controls or become loose while driving.

Fits A-Class · W177

Rear-Lamp Fastener Removal ToolC3D–01828
MercedesRemoval tools

Rear-Lamp Fastener Removal Tool

Small service adapter for more easily loosening and tightening the rear-lamp retaining fastener during bulb replacement. The creator specifies PETG plus an M5 heat-set insert, an M5×6 socket-head screw, and a DIN 9021 5.3×15 washer, and source photos show the assembled tool on the fastener. Use it only as a hand tool; do not overtighten the lamp fastener, and inspect the printed body and insert before each use.

Fits A-Class · W176