C-Class

Two-piece dual cup holder designed to insert into the centre-console cupholder while preserving access to the 12-volt socket, armrest and selector. The source supplies cup and stand STLs plus a CAD image but no container-size or crash-retention test. Use cabin-heat-resistant material, check console and selector clearance and test only with cold, closed containers before road use; confirm the assembly cannot detach or spill into controls under braking.

Fits C-Class · W203 / S203 / CL203

Two-level center-armrest organizer source-backed for 2015–2021 C-Class interiors and the corresponding GLC console. The upper tray includes Canadian coin slots, a phone compartment and general storage; the lower tray catches loose items. Source imagery is CAD and slicer evidence only. Verify the 258×123×65 mm envelope before printing, ensure the lid closes freely, and do not place items where they can jam the console or controls.

Fits C-Class · W205 / S205 / C205 / A205 · GLK / GLC · X253 / C253

Two-file mounting set for 10.25-inch and 12.3-inch aftermarket Android head units. The creator states that it lowers the display for a more factory-like position and shows the assembly installed. Verify the screen and supplied hardware are compatible, retain full visibility of the road and instruments, prevent contact with vents or trim, secure all wiring, and recheck fasteners after installation.

Fits C-Class · W205 / S205 / C205 / A205

Two-piece phone holder and mount that clicks into the factory Nokia 6110 cradle fitted to the creator's 2001 vehicle. The lower arm includes a charging-cable opening and the holder can be adjusted for other phone sizes. Compare the original cradle and device dimensions, use cabin-heat-resistant material, protect trim and wiring and verify the device remains retained without obstructing controls, airbags or sight lines.

Fits C-Class · W203 / S203 / CL203

Cup holder designed for a 2013 C180 and physically shown in its centre console, with short and long sleeves for 59 mm cans and larger containers. The creator recommends PETG or ABS for cabin heat, supports and roughly 0.16–0.24 mm layers. Match the console and container diameter, check selector and control clearance and use only closed, cool containers until retention is proven; verify the holder cannot loosen or cause a spill under braking.

Fits C-Class · W204 / S204 / C204

Clip-on rear-camera mount developed for the estate headliner and a Vantrue N4/N5 RC-01 rear camera. It clamps between the headliner and roof sheet without screws or holes and is shown installed clear of the tailgate. Fitment is limited to the estate body. Protect the headliner, keep the camera and cable clear of airbags, visibility and tailgate travel, and verify the mount cannot detach.

Fits C-Class · W205 / S205 / C205 / A205

Two cupholder inserts sized for 250 ml and 355 ml energy-drink cans. The creator explicitly states fitment across the sedan, estate, coupé, and cabriolet body variants and provides physical in-console images. Use a heat-resistant interior material, confirm the chosen insert seats fully, keep liquids clear of electrical controls, and stop use if the can can tip, bind, or interfere with the console lid.

Fits C-Class · W205 / S205 / C205 / A205

Three-piece iPhone 7 holder designed specifically for the original CD slot and shown installed in the source vehicle; the creator notes a thick phone case and charging lead. Match the phone, case and head-unit slot, use cabin-heat-resistant material, insert without forcing the disc mechanism and route the cable clear of controls. Verify that the holder cannot obscure controls, airbags or the road or eject the phone under braking.

Fits C-Class · W204 / S204 / C204

Replacement lever made after the originals broke on W203/S203 seats. The creator reports PLA loosening after sun exposure and successful use in PETG. Compare the lever shaft and seat-control version, use tough cabin-heat-resistant material, fit without forcing the switch and confirm every seat adjustment operates normally and the lever remains secure; this file does not replace structural seat or restraint hardware.

Fits C-Class · W203 / S203 / CL203

Cup-shaped storage inserts for the shared C-Class, E-Class, and GLC cupholder geometry, supplied with and without a light window and with optional coin storage. Only the non-ashtray files are included; the ember-extinguisher variants are intentionally withheld. The creator used flame-retardant ABS. Select the correct lighting version, keep the original light unobstructed, and use only for coins or other small non-hot items.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · GLK / GLC · X253 / C253

Work-in-progress umbrella holder for the C300 trunk, source-backed for model year 2015 onward and attached through existing factory holes with 1/4-20 by 1-inch bolts. Source images show both the physical brackets and their installed position. Use only for a light umbrella, preserve access to adjacent equipment, verify fastener engagement and trunk-lid clearance, and never use the printed brackets for cargo restraint or any safety-critical load.

Fits C-Class · W205 / S205 / C205 / A205

Screen-hook phone-mount bar with a 14 mm ball, designed around an MPOW wireless charger. The author supplies separate right-hand-drive and mirrored left-hand-drive files and shows both the bare part and installed phone. Bend only as required for installation behind the screen, verify the correct steering-side file, protect dashboard surfaces, and confirm the mount cannot obscure instruments, loosen, or contact controls.

Fits C-Class · W205 / S205 / C205 / A205