Boxster 986

Cup holder with a 4-inch opening designed to fit the change-holder location; the creator contrasts it with an original 3-inch-opening version.

Fits Boxster · 986

Flywheel-bolt-driven installation tool that seats the rear main seal 13 mm below the crank flange; its orientation relief clears the flywheel-flange rivet.

Fits 911 · 996 · Boxster · 986

Drop-in ashtray-delete cubby for the Boxster 986. The creator secured it with double-sided tape and finished it with black flexible interior paint.

Fits Boxster · 986

Nonfunctional cosmetic replacements for missing headlamp-washer nozzles.

Fits Boxster · 986

Replacement lever for the ventilation flap beside the ignition switch on European-market vehicles.

Fits Boxster · 986

Center-storage cup holder remix with a support that keeps the insert level and limits shifting while retaining lid closure.

Fits Boxster · 986

Double cup holder pressed into the lockable center storage compartment while retaining lid closure.

Fits Boxster · 986

Can holder fitted to the center storage compartment; the creator test-fitted it in a 2001 vehicle.

Fits Boxster · 986

Replacement for the upper square CD-case storage unit in the dashboard, with a top cable-routing port for a USB/Bluetooth module. The creator printed it in resin and reports good fit.

Fits 911 · 996 · Boxster · 986

Two-piece offset front license-plate mount comprising a curved plate bracket and screw-in tow-eye adapter. The adapter is bored for through-bolt reinforcement; the creator describes the shorter adapter as 78 mm long and suggests an approximately 85 mm M10 bolt.

Fits 911 · 997 · Boxster · 986

Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.

Fits 911 · 996 · Boxster · 986

Printable lining for a center-console-delete conversion, supplied as a full model or front/rear split for a Prusa Mk3S-size bed, plus a cover plate. The creator recommends PETG, instructs removal of the orange bracket tabs for mounting, and leaves room to upholster the part.

Fits Boxster · 986

One-piece phone-holder mount for the stock stereo with an approximately 17 mm ball. The creator says it worked with an existing holder and used foam tape beneath the ball to reduce bounce.

Fits Boxster · 986

Split-ring cap for the upper HVAC blend-door post, installed through the front-luggage-compartment access opening and secured with a small dab of superglue while keeping adhesive off the slotted plastic bearing.

Fits Boxster · 986

Removable dual cup-holder assembly whose bracket wedges between the center dashboard and upper center console. The cup holders can be stored in the armrest when not in use.

Fits Boxster · 986

Three printable shift-linkage repair inserts designed for a 1997 five-speed car. The creator specifies PETG or ABS, no supports, 40% infill and 2 mm walls, and reports positive initial road-test results.

Fits Boxster · 986

Two-piece iPhone 12 Pro Max support that replaces the CD-storage function while retaining the original surround; the two printed modules assemble with three M3 x 10 screws.

Fits Boxster · 986

Printable camshaft holding-down tool for early five-chain engines in the Boxster 986 and 911 996. The tool holds the camshafts during cylinder-head-cover removal and reassembly.

Fits 911 · 996 · Boxster · 986

Flat-backed replacement clip for retaining a front dashboard tweeter when the original plastic clip has become brittle.

Fits 911 · 996 · Boxster · 986

Dual can holder with a rectangular base and raised retaining walls, designed and test-fitted by the creator in a 2001 Boxster S 986.

Fits Boxster · 986