Find your next part.

Two-piece cover for the tow-hitch receiver opening.

Fits Model Y · First generation

Four-piece left/right front mud-guard set remixed for M3 square nuts and M3x10 mm screws. The creator thickened each backplate by 2 mm and reports the set fitted the available wheel-liner gap.

Fits Model 3 · First generation

Flexible replacement spacer for a missing exterior door-handle insert that restores the handle's flush position. The creator specifies TPU, 200°C, 10 mm/s, and 15% infill.

Fits Model 3 · First generation

Two-piece holder that relocates the trailer-hitch electrical plug directly to the tow hook for short cables. The creator specifies M6 and M5 screws, separate car- and hitch-side connectors, and a cable with at least nine wires.

Fits Model 3 · First generation

Multi-piece protective cover for the vehicle's jacking-point opening. The creator designed it as a direct replacement for a missing or damaged factory cover and states that it protects the opening from water, salt, dirt and road debris. Print TLC1, TLC2 and TLC_Clip; glue the body pieces as described and print the clip quantity needed for one cover. Reuse sound original retainers or tested automotive fixing clips. This is a protective trim cover only: remove it as required before lifting, never place a jack or stand on the print, and confirm secure retention after installation.

Fits Tonale · Tipo 965

Replacement forward-collision radar cover with thicker clips and extended coverage intended to reduce water, snow and dirt accumulation. The creator test-fitted it on a late-2018 vehicle. Remove it immediately if any radar or driver-assistance warning appears.

Fits Stelvio · Tipo 949

Clip-on shield for the original forward-collision radar cover to reduce water, dirt and snow accumulation. The creator explicitly states Alfa Romeo Stelvio and Giulia fitment and reports testing at all sensitivity settings without affecting operation. Remove it immediately if any radar or driver-assistance warning appears.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement left and right deflectors fitted ahead of the rear wheels, with an optional reinforcement pad for a flexible print. The creator reports months of use. Print the deflectors in TPU for flexibility and the reinforcement pad in a stiff weather-resistant material; verify wheel, tyre, suspension and fastener clearance before use.

Fits Stelvio · Tipo 949

Snap-on door-hinge cover designed and test-fitted on a 2018 vehicle. It fits without adhesive according to the creator. Use PETG or another cabin/exterior-heat-resistant material and confirm the cover does not interfere with hinge travel.

Fits Stelvio · Tipo 949

Replacement handle for the convertible-roof latch on the 2015 4C Spider. The creator designed it after an original handle broke and supplies both the editable Fusion 360 file and validated STL; the editable source is archived. The creator used polycarbonate for southern heat and states ABS or PETG should also be suitable. Compare the pivot and latch engagement with the broken original and verify secure roof closure before driving.

Fits 4C · Tipo 960

Extended two-piece version of the MiTo cabin-air intake water deflector, comprising the main deflector and flange. It provides more coverage than the ancestor and retains the original warning that seams may need adhesive sealing. Both validated 3MF pieces are required. PETG follows the tested material rationale of the underlying water-deflector design.

Fits MiTo · Tipo 955

Two-piece magnetic air-intake assembly for the MiTo fog-lamp aperture, including the base duct and magnet/screw plate. The source specifies 10 x 2 mm neodymium magnets and M2.5 cylindrical cross-head screws, and notes that CNC aluminium gives the best result although the files are printable. PETG or ABS is inferred for exterior heat and weather exposure. Removing a road lamp or routing brake/engine air may be regulated; verify local legality and safe hose routing.

Fits MiTo · Tipo 955

Replacement rear access cap for an Alfa Romeo MiTo headlamp housing. The source identifies the component and vehicle directly but provides no year or lamp-option split. PETG or ABS is inferred for heat and moisture resistance. Compare the tab, diameter and seal with the original before installation.

Fits MiTo · Tipo 955

Set of distinct blanking plugs for the roof-rack screw openings on a 2010 MiTo. Each position differs; retain the source orientation and test every slot before fastening. The creator notes that transparent glue can prevent proud edges and that the plugs do not provide a watertight seal.

Fits MiTo · Tipo 955

Scuttle-area deflector that redirects water away from the cabin-air intake when an aged windscreen/scuttle seal channels rain toward the vent. The creator used PETG and also sealed the joints with glue. It is an auxiliary deflector, not a substitute for repairing the drain or weather seal.

Fits MiTo · Tipo 955

Replacement bracket that holds the engine-hood release handle. The original Thingiverse page is no longer live; a lawful public mirror preserves the creator credit, CC BY licence, original source ID, STL and preview. PETG is inferred for toughness; ASA is preferred for higher heat exposure.

Fits 159 · Tipo 939

Replacement rubber-style bump stop for the underside of the Sportwagon boot lid. The creator printed it in TPU 95A with thin walls to preserve compliance. Verify lid alignment and closing force after installation.

Fits 159 · Tipo 939

Extension intended to be bonded to a modified original headlight cover when aftermarket lamps need extra clearance. Confirm engagement, sealing, heat clearance and condensation control before use. ABS is inferred for lamp-area heat; ASA or PETG are alternatives after temperature testing.

Fits 159 · Tipo 939

Replacement upper bush for the mechanism that pushes the boot lid upward when its release is pressed. PETG is inferred for repeated compression, moisture and temperature cycling; TPU is an alternative if the original part requires more compliance.

Fits 159 · Tipo 939

Tapón para deposito de agua limpiaparabrisas alfa romeo 147 JTD

Fits 147 · Tipo 937

4 part grill, just superglue the parts together, you may need to cut part of the top to allow for the badge.

Fits 147 · Tipo 937

Modified sill or rocker-trim support bracket with dimensions and geometry changed to simplify printing and increase strength. The remix and its source explicitly identify Alfa Romeo 166 fitment; compare the original bracket and mounting geometry before installation.

Fits 166 · Tipo 936

Replacement support bracket for the sill or rocker trim. The source explicitly identifies Alfa Romeo 166 fitment; compare the original bracket and mounting geometry before installation.

Fits 166 · Tipo 936

Adapter for installing the creator-linked LED fog lamp with the original fasteners on Alfa Romeo 156, 159 and Brera. The source instructs cutting the lamp tabs and securing the lamp with a zip tie in the printed groove. ABS is inferred for weather, vibration and lamp-area heat; PETG is an alternative. Confirm beam aim and legal compliance before road use.

Fits 156 · Tipo 932 · 159 · Tipo 939 · Brera · Tipo 939