Find your next part.

Glue-on repair tabs for broken mounting points on the front grille. The creator documents superglue installation and an optional filament pin through drilled 1.5–1.75 mm holes; photographs show the repair installed. These prints reproduce repair fragments rather than the grille assembly, so no grille OEM number is assigned. Verify the exact break, use weather- and heat-resistant material and adhesive, and confirm the grille is retained clear of cooling airflow and moving parts.

Fits Vito / Viano / V-Class · W639

Flexible expansion dowel for the rear number-plate mounting holes, designed so scaling can compensate for enlarged corroded openings. Source photographs show the loose child and installed location. Use weather-resistant TPU, assess and repair corrosion separately, scale conservatively, use compatible screws, and confirm the plate is secure without distorting the tailgate skin.

Fits Vito / Viano / V-Class · W639

Flexible 42 mm plug for sealing body openings in the windscreen-wiper compartment. The creator warns that rigid filament will not fit; source photographs compare printed and original plugs and show the installed locations. Print only in suitable TPU/flex, verify every opening size and drainage path, and confirm the plugs seat fully without trapping water or wiring.

Fits Vito / Viano / V-Class · W639

Flexible protective cap for the front windscreen-wiper arm nut, print-tested by the creator in 95A TPU and shown installed. Match the spindle and arm version, use UV-, weather- and washer-fluid-resistant flexible material, seat it without contacting the moving arm, and confirm full wiper travel and retention after wet-weather operation.

Fits Vito / Viano / V-Class · W639

Two-piece flexible gasket for the rear-window wiper shaft. The creator explicitly describes it as a temporary fix because typical printable TPU is harder than the original rubber; installation requires removing the rear wiper motor. Use only as a temporary non-equivalent seal, match the exact shaft and glass interface, avoid loading or scratching the glass, and verify sealing, motor alignment and free wiper movement.

Fits Vito / Viano / V-Class · W639

Replacement retention clip for the bonnet support strut. The author supplies printable STL and editable STEP geometry plus a source photograph of the physical clip. Use engine-bay-temperature- and weather-resistant material, compare the strut diameter and mounting profile, and confirm the strut is retained when stowed without weakening or interfering with bonnet support or latching.

Fits Vito / Viano / V-Class · W639

Replacement cap for the roof-trim opening. The source includes the printed cap and installed physical views; confirm the opening dimensions and trim variant before installation.

Fits E-Class · W211 / S211

Replacement rear-bumper support bracket corresponding to the exact child number identified by the creator. Print upright with high infill in ABS or polycarbonate-class material, use support only at the latch, and remove the modeled sacrificial support from the screw hole after printing.

Fits E-Class · W211 / S211

Straight and bent replacement variants for the left rear bumper retaining clip. Fitment is limited to the creator-stated chassis and side; no opposite-side or facelift applicability is inferred.

Fits E-Class · W211 / S211

Replacement rear registration-plate lamp lens for the CLK 209 series. The creator supplies two verified author models: one version retains legs for the festoon bulb and one omits those legs. Print in clear filament; the creator recommends PETG rather than PLA for improved heat and weather resistance, a 0.2 mm translucent window, and silicone sealant around the rim to prevent water ingress. Fitment is source-backed only for the C209/A209 generation.

Fits CLK · C209 / A209

Protective cap for an exposed windshield-wiper pivot bolt, shown installed by the creator and intended for PETG. The source gives no side, market or wiper-system revision. Compare the pivot and cowl clearance, use UV-, weather- and engine-bay-heat-resistant material and verify the cap cannot contact the moving arm, trap water or detach into the wiper mechanism.

Fits C-Class · W203 / S203 / CL203

Transparent registration-lamp insert with a mount for the compact CVBS/AHD camera commonly supplied with aftermarket head units. The creator explicitly states W203 and W209 fitment and recommends transparent PCTG or PETG, aligned 100% infill, no top or bottom layers and ironing. Compare the lamp opening and camera body, seal cable entries, preserve required plate illumination and verify the insert cannot detach or leak into the boot lid.

Fits C-Class · W203 / S203 / CL203 · CLK · C209 / A209

Compact reverse-camera housing published specifically for this generation. The source supplies one printable STL and one CAD image but no camera dimensions, body-style split, mounting method or environmental test. Measure the camera and mounting area, use UV-, weather- and heat-resistant material, seal cable entries, preserve licence-plate illumination and visibility and confirm the housing cannot detach or obstruct the boot lid.

Fits C-Class · W203 / S203 / CL203

Replacement grilles for the three windshield water drains, designed on a C200 of this generation. The source provides three CAD views and one printable STL but does not state body style, market or facelift coverage. Compare all three drain openings before printing, use UV-, heat- and water-resistant material, keep every drain passage open and verify water flows freely without entering the cabin or electronics.

Fits C-Class · W203 / S203 / CL203

Two rear third-brake-light cover variants. The creator recommends the file ending in “n2” for better fitment and specifies ABS rather than PLA. Exact fitment evidence is limited to the first-generation SUV; confirm the lamp housing and retention points before installation.

Fits M-Class / GLE · W163

Three-piece rear headlamp lid made after the creator lost the lid on an ML 270. Print the two rigid lid pieces in PETG or ABS, glue them together after removing support material beneath the hooks, and print the sealing insert in a flexible material. The creator suggests five perimeters and 50% infill for the first rigid piece, two perimeters and 10% infill for the second, and three perimeters and 10% infill for the flexible insert. The insert may be a tight push fit. Exact evidence is for the creator’s ML 270; confirm the headlamp housing before use.

Fits M-Class / GLE · W163

Two author variants of the left/right rear-bumper opening cover for the pre-facelift (phase 1) vehicle. Source photographs show loose printed covers and installed results. Fitment is not established for facelift bumpers or alternative bumper packages; compare the opening, tabs and side before printing.

Fits M-Class / GLE · W163

Two rear headlamp covers—one oblong and one small round cover—made by the creator for their first-generation SUV. The creator states that the small round cover needs light sanding to reduce visible faceting and recommends finishing the printed surfaces with varnish. Confirm headlamp housing and cover geometry before use.

Fits M-Class / GLE · W163

Retaining-clip variants for the exterior trim strip below the headlamp. Exact source fitment is the first-generation SUV; the creator includes an elongated version that held the strip more securely on their vehicle. Three author OBJ variants are supplied. Compare the original clip and trim engagement before choosing a file.

Fits M-Class / GLE · W163

Replacement stop/buffer reproduced by the creator as A2107500326 and explicitly tagged for CLK 208-series and E-Class 210-series cars. Mercedes official evidence identifies this exact child as an Anschlag (stop), with independent parts evidence describing a deck-lid/trunk-lid buffer. The supplied geometry is labeled with A2107500326; the earlier A2107580944 supersession is not assigned to the print. C208 coupe and W210 body/production applicability can vary, so verify the exact child by VIN and compare the original before fitting. The source does not state material, installation torque or physical validation.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Replacement retaining clip for the door weatherstrip/seal. The creator designed it after the original clip broke and reports that it performs nearly as well as the original component. Use an automotive-temperature-capable material, compare the printed clip against an intact original before installation, and replace it if the seal is not held securely.

Fits A-Class · W168

Replacement stop for the rear/tailgate door locking mechanism, identified by the creator and model filename as 6387400003. Source photographs show the loose original-style child from both sides. Use a tough, weather- and impact-resistant material, compare the mounting and contact faces with the original, preserve latch and seal clearances, and verify the rear door closes, latches, opens and remains aligned without binding before driving.

Fits Vito / Viano / V-Class · W638

Replacement cap for the windscreen-wiper spindle screw on a 1997 SLK 230. Source photographs show the physical print loose, the uncovered spindle and the cap installed. Use UV-, weather- and heat-resistant material, match the spindle and nut dimensions, press on without disturbing wiper-arm torque, preserve full arm and bonnet clearance and verify secure retention through a complete wet-screen sweep.

Fits SLK / SLC · R170

Replacement button for the deteriorated rubber retainer on the door-sill/kick-panel trim. The creator states exact SLK 230 fitment and adds a locking feature to keep the print in place; the source supplies one STL and a CAD source image but no physical installation photograph. Print button-top down in tough cabin- and weather-resistant material, compare the panel and body socket, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits SLK / SLC · R170