Find your next part.

Replacement cover plate for the motor inside the right exterior mirror, designed for model years 1998–2004 after a purchased spare did not fit. The source provides one STL and a CAD source image but no physical fit photograph. The creator warns that PLA breaks easily where the motor-screw heads press into the plate. Restrict use to the right mirror and matching motor, print flat-side down in tough cabin-heat- and weather-resistant material, fit screw heads gently and verify mirror adjustment, retention and full housing clearance.

Fits SLK / SLC · R170

Replacement housing for the rear-door magnetic bumper on 2002–2006 vans. The creator cites original reference 901 740 03 16 but explicitly says this geometry is not an exact match; therefore that number is preserved only as a reference and is not assigned. Printing requires a layer pause to encase the reused original metal components, with TPU 64D or 95A specified. Inspect rust expansion, clean and protect the metal parts, confirm door alignment and magnetic retention and verify the housing cannot detach or interfere with complete door latching.

Fits Sprinter · W901–W905

Replacement bulb socket for the clearance/parking lamp in the headlamp, explicitly identified by the creator as A2108260582 for 208- and 210-series cars. The source provides one author-downloadable STL and one CAD image but no physical fit photograph. Official Mercedes parts-store metadata identifies the exact child as the clearance-lamp socket for CLK 208 and E-Class 210. Verify VIN and headlamp variant, use heat- and flame-resistant electrically insulating material, transfer the correct contacts and bulb without damaging insulation, and test retention, polarity, lamp output, sealing and heat behavior before road use.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Replacement pneumatic coupling for the vacuum-operated headlamp height adjustment, developed for a C180 after the original connector broke and leaked. The creator sealed the printed part with nail polish to make it airtight. Match both hose and headlamp ports, use fuel/oil/heat-resistant material suitable for engine-bay vacuum service, seal without obstructing the passages, leak-test the system and verify both lamps adjust and remain correctly aimed before night driving. The moulded fragment “012502” is preserved as evidence but is not treated as a complete Mercedes part number.

Fits C-Class · W202 / S202

Small retaining pin used by the creator to mount a threshold/door-sill trim panel on this vehicle generation. Source images show the printed pin beside original-style pins and at the sill mounting points. Compare the original pin, panel hole and body socket before printing; use a tough cabin- and weather-resistant material, remove sharp edges, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits C-Class · W202 / S202

Replacement sliding clip for the upper row of the lower door/body cladding, developed and tested on a 1999 roadster. The creator reports more than three months of exterior Texas use from 27–44 °C and testing to 233 km/h, specifies vertical print orientation, grid infill and 15% infill, and warns that higher infill reduced performance. The creator was told that similar cladding on 124- and 140-series cars may use it but could not confirm that fitment, so no cross-generation link is added. Compare the original upper clip and cladding rail, use UV-, heat- and impact-resistant material and confirm the panel remains secure at road speed.

Fits SL · R129

Three-piece replacement bushing for the 16 mm ball joint between the windscreen-wiper arm and motor linkage. The creator printed it in PETG at 100% infill, fitted it around the ball joint, bonded the pieces and recommends lubrication. Match the ball diameter and linkage version, use wear-, heat- and moisture-resistant material, preserve free articulation and bench-test full sweep, parking and stall behavior before wet-road use; inspect the bonded joint regularly.

Fits SL · R129

Replacement knob for the access cover on the high-mounted stop-lamp assembly. The creator instructs removing the broken knob base, bonding this print in its place and printing sideways for strength. The cited 1297500039 number identifies the surrounding lamp-cover assembly rather than this repair fragment and is not assigned. Use cabin-heat- and UV-resistant material, choose adhesive compatible with the original plastic and verify that the cover remains secure and the stop lamp operates correctly.

Fits SL · R129

Replacement drain grommet for the plastic box below the right headlamp on the air-intake side. The creator states all 124-series chassis, a slightly tighter body fit and a changed drain shape. Use heat-, weather- and fluid-resistant flexible material, confirm the right-side box and opening, preserve an unobstructed downward drain path, and verify the grommet cannot admit water to wiring or the air intake.

Fits E-Class · W124 / S124 / C124 / A124

Two replacement shaft-lock variants for the headlamp-wiper motor assembly: K for SWF motors and L for SWF or Bosch motors. The creator tested both on original assemblies and documents the installed position. Identify the motor maker before printing, use heat- and weather-resistant material, preserve cable potting, and bench-test motor retention, full sweep and parking before road use.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grip for the thin wallet/spare key, designed to make the original key blade easier to turn. The print is only the external grip and does not reproduce the lock blade. Confirm the blade shoulder and grip fit, use tough cabin-heat-resistant material, retain the blade securely, and test gentle operation in each intended lock without forcing the cylinder.

Fits 190 Series · W201

Replacement handle modeled after the original bonnet-release handle. Source photographs document the latch area and installed handle location. Compare the pivot and cable-end geometry, use tough cabin-heat-resistant material, preserve full cable travel, and verify the bonnet opens, closes and latches correctly before driving.

Fits 190 Series · W201

One-to-one copy of an original 126-series side-skirt fastener, printed by the creator in PETG with 0.1 mm layers, organic supports and four perimeters. Source photographs show the loose clip beside the original and the relevant body-cladding locations. W126 cladding uses several position-specific fasteners, so compare the original clip before use, deburr contact edges and confirm the panel is retained without distortion.

Fits S-Class · W126 / C126

Replacement trim clip for the towing-eye cover on a 126-series car. The preserved author archive supplies the model, licence and exact fitment, while the only source image is a CAD render and no physical make is shown. Compare the original clip and cover position, use UV- and weather-resistant material, and confirm the cover cannot loosen into traffic.

Fits S-Class · W126 / C126

Two sizes of replacement plastic retaining nut copied from the headlamp, indicator and rear-lamp hardware on a US-market 123-series car. The source does not define every position, so compare the original nut, thread, diameter and lamp location before choosing a size. Use weather- and heat-resistant material, tighten only enough to retain the lamp and recheck lamp alignment and sealing.

Fits W123 Series · W123 / S123 / C123

Replacement pull handle for the bonnet release latch. The creator designed it for 123-series cars, printed it successfully, warm-formed the slight original curve and drilled the metal-pin hole after printing. Shape only while warm, retain the original metal pin, verify full latch travel and confirm both primary and safety latches engage before road use. The creator only says it may fit later 124-series cars, so no cross-fitment is assigned.

Fits W123 Series · W123 / S123 / C123

Creator-printed protective caps for exposed door and boot lock openings. Only the source-designated 20 mm door cap and 36 mm flat boot cap are retained; four alternate test sizes are excluded. Confirm opening diameter, key access where required, drainage and secure retention.

Fits Z4 · E85 / E86

Left and right headlight-washer nozzle covers, shown as a physical print. The E85/E86 source identity corresponds to the facelift bumper with headlight cleaning system S502A. RealOEM identifies primed left 51117078261 and right 51117078262 from January 2006; confirm production date, bumper, side, paint code and S502A before finishing and fitting.

Fits Z4 · E85 / E86

Small support frame that attaches the painted headlight-washer cover to the washer nozzle, shown physically installed after the creator's one-year ABS test. BMW supplies the frame only with the complete nozzle, so no parent-assembly number is assigned. Verify cover retention, nozzle extension and legal washer operation.

Fits Z4 · E85 / E86

Two-piece clip for the wheel-housing service flap, shown installed, loose and after extended use. The creator reports that PLA softened but still held after two years and recommends a more heat-resistant material. BMW does not service this clip separately from the surrounding flap, so no parent-assembly number is assigned. Verify closure and tyre, lamp and suspension clearance.

Fits Z4 · E85 / E86

Flexible replacement retaining lanyard for a broken or missing fuel cap tether in the creator's 2002 car, shown installed. No separately serviced BMW number was established for the printed tether. Confirm the cap seals and the lanyard cannot foul the filler neck or flap.

Fits Z3 · E36/7 / E36/8

Caliper-modeled replacement for deteriorated floor plugs in the creator's 1998 car, shown installed and compared with the original. The TPU print was accidentally rain-tested and reported watertight. Inspect the surrounding metal, use compatible sealant only if required, and verify water sealing.

Fits Z3 · E36/7 / E36/8

Honeycomb-pattern replacement pair for the red rear-bumper reflectors fitted to the US-market X5 M. The creator hand-measured the originals, reproduced the factory mounting features, also provides a flat adhesive-backed alternative, and documents the printed pair installed for one year. This fitment is limited to the F85 X5 M rear bumper; standard F15 bumpers and non-US configurations must be checked separately. The modeled pair replaces left reflector 63 14 7 850 005 and right reflector 63 14 7 850 006. Print in a UV- and heat-resistant automotive material, preserve rear parking-sensor clearance, and note that deleting mandated reflectors may be unlawful for road use in some markets.

Fits X5 · F15 / F85

Two-size replacement clip set for retaining the windscreen-washer hose along the underside of the hood. The creator specifies three standard clips and two 8 mm clips for the second-generation X5, and provides both an installed hood view and loose physical prints. Print in a heat-, moisture- and fatigue-resistant material, compare each clip and hose diameter with the originals, route the hose without kinks, and confirm clearance before closing the hood. No OEM number is assigned because BMW public catalogs do not establish these modeled clips as separately serviced child parts; hose and nozzle parent assemblies are deliberately not used.

Fits X5 · E70