Find your next part.

Replacement cap for the roof-rack system pictured by the creator, explicitly identified for first- and second-generation X5 applications. The source includes a physical printed cap and vehicle/rack context, but does not establish that every factory or aftermarket rail and crossbar profile uses the same interface. Compare the mating profile and dimensions with the missing cap, print in a UV-, heat- and weather-resistant material, and confirm secure retention before driving. No OEM number is assigned because the exact rack variant is not independently established.

Fits X5 · E53 · X5 · E70

Tapered adapter for mounting an aftermarket frameless Plateholder bracket to the original front bumper mounting surface. The creator designed it for a short German plate after removing the wide factory plate carrier and shows the printed adapters installed on the vehicle. Print one adapter for each attachment point, use suitable exterior-grade material and hardware, and confirm bumper style, plate dimensions, local visibility rules and secure retention before road use. This interfaces with aftermarket hardware and is not assigned a BMW OEM number.

Fits X5 · E53

Two-piece bolted replacement for missing metal staples that retain the lower-windscreen rain tray, with loose and installed physical evidence. The source's 51713401811 identifies the complete E83 windscreen-panel cover, while the printed geometry replaces its mounting feature, so that parent number is not assigned. Use a weather- and heat-resistant material, corrosion-resistant M5 hardware, and verify wiper clearance, water drainage and retention after installation.

Fits X3 · E83

Slide-on repair for a broken latch on the low-beam rear headlight dust cover, directly modeled and fit-tested by the creator for X3 E83 headlights. Molded marking 1305239123 is not an 11-digit BMW number; catalog number 63128381326 identifies the complete dust cover, not this printed latch repair, so it is deliberately withheld. Print in PETG or a higher-temperature engineering polymer and verify the cover remains sealed and removable after heat cycling.

Fits X3 · E83

Forty-millimeter funnel shaped for the windshield-washer filler opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free with the larger end upward. This is a service accessory rather than the reservoir, filler neck, or cap, so no parent component number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i4 · G26

Four-piece adjustable rear-hatch stop with a flexible buffer, modeled and trial-fitted on a 2020 120Ah vehicle to eliminate play and rattling at the closed hatch. It recreates the function of BMW adjustment element 51247361955, originally used on earlier cars, for later LCI vehicles whose lock-integrated rubber has worn. Print two assemblies as the creator specifies, use TPU for the buffer and heat-resistant rigid material for the body, screw and nut, then adjust symmetrically without preloading or misaligning the hatch.

Fits i3 · I01

Eccentric 48 mm funnel shaped to clear the surrounding structure at the windshield-washer reservoir opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free. This is a service accessory rather than the reservoir, filler neck or cap, so no parent number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i3 · I01

Flexible replacement tether joining the AC and DC fast-charge port caps to the inside of the charge door on CCS-equipped vehicles. The creator shows the printed strap installed on both caps and compares it with the original tether. Print in a durable UV- and weather-resistant flexible material, confirm that all ends seat fully, and check that the strap cannot foul the inlet, caps, hinge or door seal.

Fits i3 · I01

Replacement automatic-selector gear-indicator bezel, shown physically installed and loose for inspection. The creator specifies a filament color change: print the first layers in transparent material and the following layers in black so the markings remain legible. Automatic-transmission fitment only; compare the selector opening and indicator layout before installation. No parent selector-assembly number is assigned.

Fits 02 Series · Type 114 / E10

Four-print set of replacement fulcrum sleeves for the BMW E31 pop-up headlamp bucket, physically shown loose and installed at the upper bucket attachment by the creator after replacing warped original inserts. BMW catalogs identify the separately serviced joint sleeve as 63121392066, position 13 in the headlamp component diagram and six per vehicle. Print in heat-resistant material, replace all damaged sleeves, then verify bucket retention and have headlamp aim checked before night driving.

Fits 8 Series · E31

Replacement windshield support/adjuster for the BMW E32, shown physically installed by the creator while fitting glass. BMW catalogs identify the exact original component as support 51311948155, produced from June 1986 across E32 730i/730iL, 735i/735iL, 740i/740iL and 750i/750iL applications in LHD and RHD markets. Compare the body channel and original support before use, and leave final glass positioning and bonding to a qualified installer.

Fits 7 Series · E32

Custom front towing-eye opening cover designed and physically installed by the creator on a BMW G32 6 Series Gran Turismo with the pre-LCI M Sport front bumper. The round face intentionally differs from the curved factory-painted flap and includes a removal notch and decorative BMW relief. Use only on the matching pre-LCI M Aerodynamics (S715A) bumper opening, print in a weather- and heat-resistant material, paint or seal for UV exposure, and verify all retention tabs before road use. Genuine BMW reference 51118072209 identifies the original primed M-bumper tow-eye cover; it is not a claim that this custom round face is factory geometry.

Fits 6 Series · G32 Gran Turismo

Replacement clamp for the factory BMW E24 headlamp cleaning system. BMW catalogs identify the left/right clamp pair as 61661362211 and 61661362212 across European E24 628CSi, 630CS, 633CSi, 635CSi and M635CSi applications; 61661362211 is discontinued while 61661362212 remains cataloged without a supersession shown. Use only on cars equipped with the headlamp cleaning system, confirm side and production configuration by VIN, and test the wiper path before operation.

Fits 6 Series · E24

Two repair-stop geometries, 15.5 mm and 22 mm, for damaged stops on the chrome headlamp glass-holding frames of BMW E24 cars. BMW 63121361709 and 63121361710 identify the complete left and right glass-holding frames, not these printed repair inserts, so neither parent number is assigned. Select the matching size, use a weather- and heat-resistant material and confirm full wiper travel without lens or trim contact.

Fits 6 Series · E24

Washer-fluid filling funnel for BMW G30 and G31 models and potentially other 5 Series or 7 Series vehicles using the same filler neck. The documented source gallery shows the funnel installed in a G30/G31 filler neck, so only those directly verified generations are linked here. Print in PETG with a 0.4 mm nozzle. Keep the funnel clean, remove it after filling, reinstall the original cap fully, and wipe away spills before driving.

Fits 5 Series · G30 / G31 / G38 / F90

Attaching the trailer socket bmw e60 / e61 Retain only the socket mounting bracket; verify trailer wiring and legal requirements independently. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Screw clip for BMW sub-panels. I used it for e60 100% infill (or less is also good) 0.2 layer hight Creator reports using this 30 mm screw clip on an E60 under-panel. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Rear wiper gear BWM E60 Creator supplies physical comparison evidence. This rear-wiper part is for the E61 Touring body, not the E60 sedan. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Replaces the integrated plastic tab that commonly shears off, allowing the fog light to be secured without replacing the entire bumper. The bracket replicates the factory slot geometry. Once bonded, the fog light housing slides into the bracket and locks into place using the original mounting hardware/method. Material: Would recommend ASA or ABS. Compatibility: 2001–2004 (Facelift / LCI) BMW E39 5-Series models. Will not fit Pre-Facelift or M-Sport/M5 Bumpers. I also sell the printed parts: Installation Instructions: 1. Access: Gain access to the fog light assembly either by removing the front splash guard in the wheel well or by removing the front bumper entirely. 2. Alignment: Leave the fog light attached to the bumper by its remaining intact mounting point. 3. Test Fit: Position the repair bracket and verify that it makes flush contact with the bumper surface. Ensure the circular tab on the fog light housing slots correctly into the bracket. 4. Preparation: If remnants of the broken original bracket interfere with the fitment, trim them down until the repair bracket sits flush. 5. Bonding: Thoroughly clean the contact areas on both the bracket and the bumper. Apply a strong epox Creator limits fitment to the facelift/LCI bumper. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Prefer to use Nylon or another filament with great cohesion (My clips was printed with Nylon-GF) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

hey ho, got a couple of used AC Schnitzer type 2 rims with the center hub caps missing, so i designed a simple and clean version. may require some sanding and spraypainting afterwards to fit your rim color. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Ther is the Mirror cover bmw e39 latch instead broken one! For each cover you need 2 direct and 2 mirror printed parts. Just put on things to the broken parts, try to put cover on mirror (i need to cut height for 2 of them) and fix it with glue. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

My E39 Touring was missing one of the clips to hold in the plate bracket (plinth). The previous owner had used silicone to hold the panel on. Unable to live with this I contacted the dealership - who were unable to find the part in their system. Doubting their competence I checked realoem myself and actually couldn't find a part number. So I turned to Fusion360 and whipped these up. I've never designed anything before so please bear with me. I have made two revisions of this thing. **(bmw_plate_plinthe_v3)** The first is a copy of the original - fits snug and locks nicely. - It may be a good idea to use a bit of RTV or Butyl Rubber around the hole to keep water out! **(Nut.stl /Thread.stl)** The second is a threaded option. Allowing you to fit an M8x1.25 nut on the back. This option was created for people who may have corrosion around the hole thus making it too big for the snap in option. Printed these on my CR-10S w/ 99% concentric infill 5 walls and 0.12 layer height @ 35mm/s Hopefully they can be of use to someone else too. Cheers. Apparently fits these models too! BMW E30 318i M10 1.8L BMW E30 318i M42 1.8L BMW E30 318is M42 1.8L BMW E30 325i M20 2.5L BMW E30 325is M20 2.5L BM Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

My BMW E39 5 Series was missing the selection switch for the power mirror. (I don't know how the previous owner could rip that thing off...) Here you can find a custom-made replacement switch. Just push it into its place. If you have any ideas for improvement, please feel free to contact me. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39