Find your next part.

5mm Cable Holder Headlight Bracket Wiring Harness Trim Clip cable clips used to hold the headlight wiring under the hood, redesigned to be easy printable OEM: 61138350827 Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

i bought RHD mirrors to my LHD e46 non-M Coupe and I created this raisers in order to get a better view angles (close to regular mirrors). This can be use to rise the angle of either side of the mirror and can be used in both mirrors. So with this you can "transform" RHD to LHD and viceversa. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

Many of these filters for the windshield washer reservoir get's broken and fall down into the water. The design is using the filter of the old holder and fits nice into your windshield water reservoir. Cut of the filter from the old holder. Glue it on the bottom. Cut off everything protruding. Done! The bar helps you to get the filter out for cleaning. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

This is an updated set of Murat's clips which fit on the facelifted E46 kidney grills (My car is a 2002 325i wagon) and work without any filing / cutting / modification of the 3D printed part. How to use: Follow Murat's instructions for trimming the existing clip sockets on the kidney grill plastic (leaving ~1mm left + socket depth). Install as suggested by them (use a small flathead screwdriver or similar to pry the metal tabs of the hood into the printed groove on the clips. My printed parts are numbered and lettered to indicate where they go on the grill. How to read the number/lettering: When standing in front of the car and looking at the grill, there is a Left and Right grill. On each Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Cap for BMW 3 Series E46 washer fluid reservoir. Excellent friction fit when printed in PETG Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Fixes the third brake light from falling off the glass. replaces the usually broken clips. Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

Four-piece E36 bumper-inlet duct inspired by the Dinan layout and physically shown installed between the bumper opening and air filter. Print in heat- and impact-resistant material, bond the sections securely, and verify filter, fan, belt, water-ingress and road-clearance conditions on the exact car.

Fits 3 Series · E36

Rear-cap extension physically fitted to an original BMW E36 fog lamp to clear the cooling fan on an LED replacement bulb while retaining the stock cap. Check bulb legality, connector strain, weather sealing, lamp clearance and heat before road use.

Fits 3 Series · E36

Replacement tow-eye opening cover for the E36 M-Technic/M3-style rear bumper, physically compared with the original and shown installed. The creator reports a tight fit and optional spring-clip provision. The nearby catalog number identifies the parent trim panel, so no OEM number is assigned.

Fits 3 Series · E36

Small repair cap for a damaged front-door tweeter grille on a BMW E36 325i. The source photo shows the original damage and repaired physical cover. Verify the cap cannot contact the speaker cone or loosen into the door.

Fits 3 Series · E36

Screw-on protective cover for exposed E30 front wheel-bearing spindle surfaces during restoration, washing, blasting, painting or storage. It is physically shown on the spindle and is removed before wheel-bearing assembly.

Fits 3 Series · E30

Replacement clip retaining the bulb holder in early E30 taillights, printed in PETG and physically installed. Late-light fitment is unconfirmed. The creator-listed 63211376879 resolves to an unrelated rotary knob in BMWFans, so it is intentionally omitted.

Fits 3 Series · E30

Click-fit cosmetic cap designed around the E30 wheel-lock bolt and physically fitted. The creator-listed 36131182006 identifies a complete lock set, not the printed cap, so no OEM number is assigned. Verify the cap cannot loosen near the wheel.

Fits 3 Series · E30

Replacement bracing cover for early-model E30 fog lamps, reproduced from the original and physically compared after a fit-improving revision. BMWFans confirms cover 63171373577.

Fits 3 Series · E30

Five-file replacement centre-cap system for factory-style 14-inch E30 basket-weave wheels, using a face, locking clip and choice of three hex inserts. The source shows physical installation; test one assembly and verify positive retention before road use.

Fits 3 Series · E30

Replacement plastic grommet used at E30 grille and rear license-plate mounting points, physically compared with the original. The creator also lists E36, E46, E90 and E92 applications; BMWFans confirms grommet 51131840154.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +1

Two replacement plastic pieces for the late-model E30 headlamp adjusting screw, copied from the originals and shown assembled on the screw. BMWFans confirms adjusting screw 63121385397. Form threads carefully and verify beam adjustment and retention.

Fits 3 Series · E30

Reinforced replacement lower wiring cover for E30 door mirrors, copied from the original and physically fitted. The supplied geometry is LHD; mirror it for RHD. BMWFans confirms left/right LHD 51161937441/442 and RHD 51161937443/444.

Fits 3 Series · E30

Replacement high-beam headlamp spacer for both Hella and Bosch E30 lamp frames, reproduced from the original and physically fitted. BMWFans confirms intermediate piece 63121362036.

Fits 3 Series · E30

Four-part replacement centre-cap system for 15-inch BBS RZ Style 5 wheels used on E30. The creator prototyped and fitted it, documents assembly and temperature-resistant materials, and advises checking the printed nut position regularly. The separate 68 mm badge number is intentionally omitted.

Fits 3 Series · E30

Replacement bushing for the E30 wiper-arm pivot on the passenger side of LHD cars or driver side of RHD cars. It is dimensioned for the standard M22×5.5 nut and physically fitted; BMWFans identifies 61611370387 as the corresponding covering cap.

Fits 3 Series · E30

Two-piece replacement cover and holder for securing the spare wheel in the E30 luggage compartment, shown physically installed. Confirm thread engagement and wheel retention before driving.

Fits 3 Series · E30

Dimensioned replacement switch knob for the Hella-style interior dome light used in BMW E12, E21 and E30. Physical prints are shown on the lamp. The creator-listed numbers identify complete lamp variants rather than this knob, so no parent-assembly number is submitted.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E12

Center cap designed and physically fitted to the 6×13-inch BBS-Mahle KBA40179 BMW Motorsport wheel used on E21. Refurbished wheels may vary, so test one cap and verify secure retention before road use. The badge number mentioned by the creator is not assigned because it identifies the separate adhesive emblem.

Fits 3 Series · E21