Find your next part.

Replacement expanding nut for securing front trim, grille and valance pieces on the BMW E21. The creator physically fitted the part and recommends flexible, heat-resistant PETG at full infill. Confirm hole diameter, screw engagement and trim retention.

Fits 3 Series · E21

Replacement stand-off spacer for fitting AUTOID rear carbon-fibre wheel-arch extensions to the BMW G42 M240i. The source is specific to that aftermarket arch kit and does not establish G87 fitment. Print in ASA, ABS, nylon, or another exterior-grade heat- and weather-resistant material, and verify the 12.4 mm diameter, 26.05 mm height, fastener engagement, arch alignment, and wheel/tyre clearance before road use.

Fits 2 Series · G42 / G87

Reusable washer-fluid filler funnel for the BMW F20 filler neck. This revision adds an O-ring groove for a stable, sealed seat, and the source image shows the printed funnel in use while filling the reservoir. Select a fluid-compatible material and remove the funnel before closing the bonnet.

Fits 1 Series · F20 / F21

Direct replacement cap for the automatic-headlight rotary switch used in BMW E82 and E88 1 Series, E90/E91/E92/E93 3 Series, and E84 X1 interiors. The keyed hex and rotation stop reproduce the functional interface, and the creator shows the printed knob installed. Reuse the original switch mechanism; no complete headlight-switch assembly is included.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E90 / E91 / E92 / E93 · X1 · E84

Replacement exterior trim bezel for the roof antenna on a Jeep Commander. The creator updated the geometry for fit and documents the broken original beside the printed replacement.

Fits Commander · XK / XH

Replacement access flap for the Jeep Commander front wheel-well liner. The source gallery documents the printed panel and its installation in the liner opening.

Fits Commander · XK / XH

Replacement back shell plate for the rear camera assembly on a Jeep Renegade.

Fits Renegade · BU

Pair of rear license-plate mount extenders for securing a standard US Washington plate to all four sockets on a Jeep Renegade. Each accepts a press-fit M6 nut and uses short low-profile screws.

Fits Renegade · BU

Replacement wheel-well access cover for servicing the fog lamp on a Jeep Renegade. The creator measured the surviving original and reports this more-rigid replacement working.

Fits Renegade · BU

Hand knob for removing the M8 spare-wheel retaining bolt in a Jeep Renegade without a separate tool.

Fits Renegade · BU

Replacement protective cap for the exposed windshield-wiper arm nut on a Jeep Renegade, recreated after the original cap was stolen.

Fits Renegade · BU

Replacement sealing plug for the Westfalia detachable towbar receiver used on a Jeep Renegade. It closes the receiver opening when the detachable towbar is removed.

Fits Renegade · BU

Printable replacement for the hood prop-rod retaining clip used on Jeep Patriot and first-generation Compass vehicles. The creator iterated the snap fit for printing without supports; both STL and STEP geometry are included.

Fits Compass · MK49 · Patriot · MK74

Replacement retention clip for the rear tail-lamp assembly on a 2015 Jeep Patriot. The third-iteration geometry uses one #8 x 1-inch screw and avoids breaking the original clip during bulb service.

Fits Patriot · MK74

Vehicle-fitted hook bracket for hanging a compact camping lamp from the upper cargo-area trim in a Jeep Patriot. The creator documents the printed bracket and lamp installed at the open tailgate.

Fits Patriot · MK74

Replacement cover for the easily broken tail-lamp screw access points on a 2018 Jeep Compass. The creator documents both cover locations installed beside the rear lamp.

Fits Compass · MP

Snap-in license-plate holder designed for a 2019 Jeep Compass. An M4 x 14 mm screw bends the holder slightly to lock it in place; the creator recommends a soft backing to prevent paint scratches and rattling.

Fits Compass · MP

Adapter for fitting an older Omix-Ada 11020.01-style rear-view mirror to the newer windshield frame in a 1981 Jeep CJ-7. The source documents the printed adapter and physical installation.

Fits CJ · CJ-7

Two-piece replacement windshield hold-down knob for a 1981 Jeep CJ-7. A three-eighths-inch fastener is inserted into the printed knob and retained by the separate tapered cap.

Fits CJ · CJ-7

Replacement translucent cover for the illumination bulbs inside a Jeep CJ-7 speedometer assembly. It reproduces the small heat-damaged factory diffuser and the source documents the corresponding CJ dashboard.

Fits CJ · CJ-7

Replacement plastic headlight-bucket adjuster for a 1985 Jeep CJ-7. It reuses the original adjuster bolts, replaces the factory rivets with small machine screws, and remained in service after five months.

Fits CJ · CJ-7

Upper and lower flexible bushings for mounting the front grille to the body on late-1970s Jeep CJ-5 and CJ-7 vehicles. Flat- and recessed-upper variants plus the lower bushing are included for TPU printing.

Fits CJ · CJ-5 · CJ · CJ-7

Pair of hollow extensions that fit over the existing windshield hood blocks on Willys CJ-2A, CJ-3A, and CJ-3B vehicles. Hard- and soft-corner variants raise the folded windshield and are documented physically on a CJ.

Fits CJ · CJ-2A · CJ · CJ-3A · CJ · CJ-3B

Replacement panel for the Gladiator JT bed opening with provisions for one accessory switch and one twelve-volt socket. It fastens to four M4 rivet nuts and the source shows both the factory opening and completed installation.

Fits Gladiator · JT