Find your next part.

Replacement windshield-washer reservoir filler neck supplied as a primary neck plus mounting bib, with an alternate split-neck version for smaller printers.

Fits 928 · 928

Small cover for the windscreen-wiper spindle nut on 1990s vehicles. The source shows the physical cover fitted around a wiper pivot and supplies one STL, but states no material or print settings. Match the spindle and nut dimensions, use weather-, UV- and heat-resistant material, preserve full wiper-arm clearance and verify complete sweep and secure retention before road use.

Fits G-Class · W463

Replacement clip for BMW door-sill/entry trim panels. The creator explicitly lists E21, E30, E36, E39, E46, E81/E82/E88, F20, E85 and related applications and identifies genuine BMW clip 51471840960. Verify the receiving-hole and trim thickness before fitting.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 3 Series · E21 +5

Door-hinge packing shims in three thicknesses. They also separate dissimilar metals to help reduce electrolytic corrosion

Fits Series · 2 · Series · 2A

Scanned right-side F30/F31 headlight support bracket shown fitted in place by the creator. Use exterior-rated material and verify retention, weather sealing, lamp aim and washer operation before driving.

Fits 3 Series · F30 / F31 / F34 / F80

Mounting clip replacement for the BMW E46 kidney grill. The kidney grills are held in place in the bonnet through flexible lips, which become brittle with time and heat exposure. My car is 14 years old and the kidney grills had lost their grips a while ago and were about to fall over. The quick fix was to string them up from the inside, but hardly an elegant fix for a BMW! Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Replacement translucent lens for the shared interior room-lamp assembly used on 1984–1995 pickups.

Fits Camry · 1st Gen · Camry · 2nd Gen · Hilux · 4th Gen +1

If you mount the MRC7354 "Soft Top Front Seat Belt Bar For Land Rover Defender / Series" the tube do not fit very well the the capping. This part gives it a nice an stable connection. Needs tu be drilled trough after mounting fpr a tight fit. Drill 8 mm oder 5/16 "

Fits Defender · 200 Tdi · Defender · 300 Tdi · Series · 2 +2

My Driver side tab cracked in half. It would be a party when on the highway/ move excessively on bumps. Mirror it for the driver side !! PRINT WITH SUPPORTS !! There's a hidden pocket in the tab, you wont see the supports but it will make it print. Creator installed the repair after a cracked driver-side tab caused lamp movement; mirror the right-side geometry for the opposite side and verify beam aim after installation. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Replacement tow-eye opening cover for the E46 M-Sport front bumper, refined through several physical prototypes and shown installed. The creator notes that standard SE geometry does not fit this bumper. Use exterior-rated material and verify secure retention without obstructing the tow-eye opening.

Fits 3 Series · E46

Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Replacement mounting shell for the factory reversing camera in the 2014 tailgate handle assembly.

Fits Tundra · 2nd Gen

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Replacement carrier plate for the exterior mirror glass, physically shown loose and installed on the mirror mechanism. The creator states that it accepts both twist-on and clip-on brackets. This is a mirror-glass support, not the complete mirror assembly; verify secure engagement, adjustment range, heating-wire clearance and an unobstructed field of view before driving.

Fits Z4 · E85 / E86

This fits a BMW F11 and maybe also other BMW cars from around 2015. If the old cable brakes, this is a replacement of the ring at the cap and the cable. The original ring has to be removed from the fuel cap. Be careful not to brake anything else then the turning ring. Use side cutting pliers or a similar tool. The put the new ring onto the fuel cap. If the ring does not fit you can also adjust the width in the attached model and re-export. I used TPU 95 for the print. Nozzle diameter can be 0.25 - 0.4, all work. I printed with supports but this leaves a rough finish. This also leads to the fact, that the ring does not slide as good as the original one. But overall it works. Don't forget to like if you like. Creator reports the TPU replacement fits and works on an approximately 2015 F11, while noting rough support surfaces can make the ring slide less freely. The editable FreeCAD source is retained for measured adjustment. Do not force the ring or damage the fuel cap. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

The mirror adjuster on my E39 stopped moving the mirror in left-right direction, however I could still hear the small motor working. After removing the mirror plate, I found a small plastic component broken. Of course you can't buy this part, only the whole assembly (the one where I marked the pins with red arrows) for 100 USD :). Based on the broken component, I copied the part and printed it. It works perfectly!! Please note that if you need this for up-down motion, you will need to mirror the part before printing. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Replacement E30 exterior door and fender moulding clip. The creator reports that the imperfect reproduction holds tightly. Listed numbers 51131953927 and 51131965105 identify parent moulding assemblies, so no OEM number is assigned.

Fits 3 Series · E30

Replacement ball connector for the 1984–1986 Celica Supra fog-light adjustment assembly, reported successfully printed and fitted by its designer.

Fits Supra · 2nd Gen

Support for the interior third brake lamp, shown as a physical print and fitted at the base of the rear window. The source does not state body-style, market or production-break coverage, so compare the lamp, parcel shelf and rear-glass profile before printing. Use UV- and cabin-heat-resistant material, preserve the full illuminated area and wiring clearance, secure the lamp against vibration and verify operation and rear visibility before road use.

Fits C-Class · W202 / S202

Retaining clip with a safety tab for one side of the front towing-eye cover; the creator instructs mirroring the model for the opposite side. Only CAD/source screenshots are available, so compare the original cover and clip geometry carefully. Use UV-, weather- and impact-resistant material and confirm the cover remains retained at road speed.

Fits 190 Series · W201

This is the buffer that the arm on the boot/trunk hits to stop it opening too far, if it cracks (which it will) then ultimately it tries to bend the gas struts. Photo shows a broken one and the print. This is for the RHS looking at the rear of the vehicle. The LHS is identical but mirror image. Print this so it stands on the long edge (hole and pin are horizontal) or the the arm will seperate the layers, there is a lot of force there. I used PETG at 100% infill. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

My BMW E39 was missing some fan grille parts for the rear seats. The CAD drawings have the exact same size as the original parts. So it just depends on how accurate your printer is (I had to sand down some areas). As you can see in the pictures you will also need a small piece of sheet metal that acts as a spring. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Fits Cherokee / Liberty · XJ

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Fits Cherokee / Liberty · XJ · Comanche · MJ