Find your next part.

Replacement captive screw-nut insert for the Cherokee XJ front grille. The creator recommends PETG or ABS for service temperature and durability.

Fits Cherokee / Liberty · XJ

Plain push-fit center cap modeled for the approximately 64 mm stock wheel opening on a 1992 Cherokee XJ. This entry excludes the decorative lettered variant.

Fits Cherokee / Liberty · XJ

Clip-on retainer that holds a broken rear washer nozzle together on a 1997–2001 Cherokee XJ wiper arm without adhesive.

Fits Cherokee / Liberty · XJ

Multi-piece left- and right-side replacement end caps for factory Cherokee XJ side steps. The sections are bonded after printing and the screw piece must be tapped before installation.

Fits Cherokee / Liberty · XJ

Clear-print replacement lens for the rear cargo lamp in a pre-facelift Cherokee XJ. The creator notes that its edges are straight rather than curved like the original.

Fits Cherokee / Liberty · XJ

Small right-side lower trim replacement for a pre-facelift four-door Cherokee XJ, positioned between the passenger door and rear wheel arch. It is not intended for the two-door body.

Fits Cherokee / Liberty · XJ

Slotted replacement for the failed plastic pivot in a Cherokee XJ electric door mirror. The slot lets the wiring pass through so the mirror does not need complete disassembly.

Fits Cherokee / Liberty · XJ

Replacement door-speaker grille for full-size Jeep doors. The source photograph compares the printed grille with the surviving factory grille frame.

Fits Cherokee / Liberty · SJ · Wagoneer · SJ

Single auxiliary-light bracket for the cowl or lower A-pillar mounting area of a Wrangler JL.

Fits Wrangler · JL

Bumper adapter for installing a three-inch pod light in a Wrangler JL fog-light opening. The creator reports successful use and recommends ABS, PETG, or ASA.

Fits Wrangler · JL

Press-fit removable cover for the exposed door-lock keyhole on Wrangler JL and JLU models.

Fits Wrangler · JL

Insert used in pairs to fill the license-plate mounting holes in an AEV rear bumper before the plate screws are installed on a Wrangler JL.

Fits Wrangler · JL

Printable W-type retaining clip sized for the fender-flare slots on 2018-and-newer Wrangler JL and compatible Gladiator JT applications. This entry uses the creator's support-free revision.

Fits Gladiator · JT · Wrangler · JL

No-drill mount for a Midland MXTA25 low-profile antenna on the internal sport-bar fastener of a two-door 2018-and-newer Wrangler JL. The location is shared with soft-top hardware.

Fits Wrangler · JL

Inner bushing for the Rampage Hi-Lift jack carrier that limits fore-and-aft movement of its horizontal carry bolt and reduces rattling. The creator states JK and JL fitment.

Fits Wrangler · JK · Wrangler · JL

Three-piece flexible replacement tether for the Wrangler JK fuel cap. The pins are intentionally snug and may be warmed slightly for assembly.

Fits Wrangler · JK

Printable floor drain plug stated by the creator to fit Wrangler JK, Wrangler JL, and Gladiator JT floors and compatible drain openings in their floor mats. This entry contains only the functional plug body.

Fits Gladiator · JT · Wrangler · JK · Wrangler · JL

Push-fit center cap for Wrangler JK steel wheels with an approximately 65 mm center bore and 84 mm outer face. This entry uses the creator's plain, no-logo geometry.

Fits Wrangler · JK

Replacement arrow-head retaining clip modeled from the Wrangler JK rear fender-flare fastener. Print in a strong, heat-resistant material with controlled flex.

Fits Wrangler · JK

Extender that restores contact between the Wrangler JK tailgate bump stop and a spare tire after fitting offset aftermarket wheels. It accepts the original bump stop and an added rubber isolator.

Fits Wrangler · JK

Bushing spacer developed on a 2008 Wrangler JK to secure a loose front inner-fender splash guard after custom fenders were fitted.

Fits Wrangler · JK

Thin snap-on protector for Wrangler JK door hinges that shields painted hinge faces from gravel impacts. This entry uses the creator's latest bulged-fit revision.

Fits Wrangler · JK

Replacement internal divider that prevents red and white light bleed inside the TJ taillight after the original metal separator rusts away.

Fits Wrangler · TJ

Flexible replacement tether sized for the stock 1997–2006 TJ fuel cap, with a split ring that allows installation without removing the cap.

Fits Wrangler · TJ