Find your next part.

Replacement mounting shell for the factory-style reversing camera on 2016–2018 Toyota RAV4 models, with author-provided ABS scaling and support guidance.

Fits RAV4 · 4th Gen

Replacement upper cushion for the luggage door of the second-generation Toyota RAV4, replacing the small factory piece that is easily knocked out.

Fits RAV4 · 2nd Gen

Protective grille for an eight-inch custom subwoofer installation in a 2006 RAV4.

Fits RAV4 · 3rd Gen

Five-piece mounting system for centring an aftermarket reverse camera beneath the third brake light on the 2006–2012 RAV4. It reuses the factory screw locations, clears the rear wiper, and was tested through an automatic car wash.

Fits RAV4 · 3rd Gen

Replacement flexible roof mounting plugs for the first-generation Toyota RAV4, with solid versions for vehicles without a roof rack and pierced versions for vehicles retaining the factory rack.

Fits RAV4 · 1st Gen

Adapter for installing Audi switch 8D0941563 in the right-hand-drive Toyota Supra Mk4 right-side centre-panel switch position

Fits Supra · 4th Gen

Replacement left and right lower-back finish trims, vibration-isolating end pads and optional mounting nut for the facelift third-generation Supra centre taillight panel. Use strong, vibration-resistant filament for the trims, soft TPU for the pads, and provide a separate watertight seal at the outer mounting holes.

Fits Supra · 3rd Gen

Replacement M5 locking nut for the second-generation Celica Supra fog-light adjustment assembly.

Fits Supra · 2nd Gen

Replacement front-grille clip for the second-generation Celica Supra, using a short piece of filament as the transverse retaining pin.

Fits Supra · 2nd Gen

Reinforced replacement clip that retains the hood-release cable at the latch mechanism, designed and installed on a 2007 vehicle.

Fits Sequoia · 1st Gen

Replacement protective grille for the FJ Cruiser snorkel intake, with standard and flat-backed printable variants.

Fits FJ Cruiser · XJ10

Heat-resistant replacement cap for the exposed windshield-wiper arm pivot fastener.

Fits FJ Cruiser · XJ10

Two sizes of fitted roof-panel plugs for covering the factory roof-rack mounting openings on the 2007 FJ Cruiser.

Fits FJ Cruiser · XJ10

Mounting bracket for the factory panoramic-view or multi-terrain-monitor front camera in TRD Off-Road and TRD Sport grilles.

Fits Tundra · 3rd Gen

Bracket and actuator lever for adding a central-locking solenoid to the 2015 tailgate latch.

Fits Tundra · 2nd Gen

Replacement linkage-rod clip for the tailgate handle, modelled for a 2006 vehicle. The original and strengthened revisions are included.

Fits Tundra · 1st Gen

Drain connector for routing the hoses from a roll-up tonneau cover on a 2025 bed.

Fits Tacoma · 4th Gen

Adapter that routes a retractable tonneau-cover drain hose through the factory bed drain.

Fits Tacoma · 4th Gen

Small clip for routing accessory wiring neatly along the rear-view-mirror stem.

Fits Tacoma · 3rd Gen

Drain fitting that joins the tonneau-cover hose to the factory bed drain without drilling.

Fits Tacoma · 3rd Gen

Clip-on holder that keeps the tethered fuel cap secured to the inside of the open fuel door.

Fits Tacoma · 3rd Gen

Small L-shaped rain shield for an aftermarket reversing camera fitted to this generation.

Fits Tacoma · 2nd Gen

Five-piece 120 mm ventilation-fan mount and air-guide set for a regular-cab SnugTop camper-shell side window.

Fits Tacoma · 2nd Gen

Replacement cap for the windscreen-washer fluid reservoir, modelled and tested on a 2001 vehicle.

Fits Tacoma · 1st Gen