Find your next part.

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Fits Series · 3

Replacement centre cap for a Discovery 3 alloy wheel. Confirm wheel and bore dimensions against the original before printing.

Fits Discovery · 3

Shield that prevents the inner rear parking sensors from detecting a raised aftermarket tow hitch. Print two in ASA or another UV- and heat-resistant material.

Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320

Replacement trim plug covering the rear-wiper-arm retaining nut. PETG is recommended for sun and heat resistance

Fits Discovery · 3

Replacement wheel cap.

Fits 924 · 924 · 944 · 944

Left- and right-side bumper pads.

Fits 944 · 944

Lower movable mounting bracket for an Alfa Romeo Stelvio headlight, designed as an alternative to the complete headlamp repair kit.

Fits Stelvio · Tipo 949

Clip-on rear-camera mount developed for the estate headliner and a Vantrue N4/N5 RC-01 rear camera. It clamps between the headliner and roof sheet without screws or holes and is shown installed clear of the tailgate. Fitment is limited to the estate body. Protect the headliner, keep the camera and cable clear of airbags, visibility and tailgate travel, and verify the mount cannot detach.

Fits C-Class · W205 / S205 / C205 / A205

Exterior rear-window cover for the estate body, replacing the corroded metal cover around the rear-wiper shaft. Bond with automotive glass adhesive or sealing silicone and retain the source-stated estate-only fitment.

Fits E-Class · W211 / S211

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement cover for the front-right opening in the side-member/sill cladding. Source photographs show the installed location, the original and printed pieces, and the CAD model. EPC evidence identifies the right-front covering; use UV-, weather- and impact-resistant material, inspect the mounting opening for corrosion, and confirm the cap remains secure.

Fits 190 Series · W201

Replacement frame for a broken rear number-plate lamp, also usable as a cutting guide for a new seal. The creator states fitment across 123-series variants. Use UV- and heat-resistant material, preserve the original lens, bulb holder and wiring, install an appropriate gasket and confirm lamp visibility, weather sealing and wire clearance.

Fits W123 Series · W123 / S123 / C123

Replacement ball outlet for a cracked headlight-washer nozzle, shown loose and fitted to the original sprayer. The creator bonded the PLA part with water-resistant adhesive and notes that the bore may need careful finishing. No complete-nozzle parent number is assigned; verify sealing, spray direction, cover clearance and legal washer operation before driving.

Fits Z4 · E85 / E86

Replacement rear access cover for the high-beam bulb opening on facelift headlamp assemblies. The creator replicated a perished cover from a 2005 vehicle, physically printed the replacement in ABS and reused the original rubber seal. Public BMW catalog evidence identifies the serviced high-beam cover as 63 12 6 940 252 for facelift E53 headlamps. Use only on matching 10/2003-on headlamp assemblies, transfer an undamaged seal, use heat-resistant material and confirm a dry, secure seal before driving.

Fits X5 · E53

Replacement covering cap for the rear-window wiper arm, 3D-scanned from the original and physically shown loose, compared with the original and snapped onto the arm. BMW catalogs identify the original child component as 61687407276, rear-wiper diagram item 6, for X3 G01/G01 LCI, X3 M F97/F97 LCI and iX3 G08; Hubauer records supersession to 61625A9D577. Use ABS, ASA, PETG or another UV- and heat-resistant material, compare the clip geometry, confirm by VIN and verify secure retention and full wiper travel.

Fits iX3 · G08 · X3 · G01 / F97

These headlamp adjusters are for the BMW E39 series (5-series from 1996 onwards). The originals are made of some material that gets super brittle with age, and pretty much self destruct. Thus making the headlamps aim far too low, and wobble when driving over the slightest dump. BMWs own solution is to supply new lamps as complete units, price probably approaching $1000. To fix, you need to take the headlamp units apart, which is actually quite easy. There are various instructions on the net, The two manual adjusters simply fully unscrew to release. The third adjuster, connected to a motor, is released by turning the exposed 5mm plastic nut 90 degrees (not all variants have this feature). One word of warning: Do not touch the reflectors, they are very easily destroyed by attempts of cleaning. You need one of each of these per side. They will work for the early halogen units, but may need modification for "angel eyes", and I have no idea about Xenon. Note also that the shape is different from the originals. I believe these may be slightly better - the originals were limited by what you could do with casting. For best strength you should ideally print them laying down, but then some s Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Cut off the remains of the rubber part on your windshield cowl and attach these printed ones. OEM PART: 51718208483 Mirror the end part to use it on the other side. Print multiple mid parts to cover the entire length. Printed from Fillamentum Flexfill 89A. Using 0.15mm layer height is important as there is a steep overhang on the part, which wouldn't print well using thicker layers. The end part might not fit perfectly but it did the job already so I didn't tweak it anymore. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Print standing vertically, Coat with a clear Just glue on your trim and push it on Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Blank plate for the E36 standard or M-style bumper fog-lamp opening, physically shown installed. The creator provides screw or drilled tie mounting. Use exterior-rated material and verify the plate is securely retained and does not obstruct required lighting or cooling.

Fits 3 Series · E36

Pair of front license-plate brackets for a 2015 Grand Cherokee WK2 lower grille. Each bracket accepts a plate screw and fastens to the mesh with a zip tie, avoiding drilled holes; the creator documents the exact mounting location.

Fits Grand Cherokee · WK2

Replacement square peg for the Grand Cherokee ZJ headlight-adjustment mechanism.

Fits Grand Cherokee · ZJ / ZG

Replacement headlight closure-panel lock ring modeled for a 1996 Grand Cherokee ZJ. The creator identifies possible use across the 1993–1998 generation.

Fits Grand Cherokee · ZJ / ZG

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Fits Grand Cherokee · ZJ / ZG