Find your next part.

Flexible grommet sealing the windscreen-washer pump to the reservoir on a 300D. The creator specifies flexible filament and 100% infill. Clean the reservoir opening, compare both pump and tank diameters, use washer-fluid-compatible TPU and confirm a leak-free seal before closing the bonnet.

Fits W123 Series · W123 / S123 / C123

Replacement headlamp mounting nut shown beside the original physical component. Compare the thread, diameter and lamp position before use, print in heat- and weather-resistant material, tighten only to the original retention load and verify headlamp aim and stability after installation.

Fits W123 Series · W123 / S123 / C123

Flexible replacement cap for the windscreen-washer reservoir, printed by the creator in TPU without supports. Compare the filler-neck diameter, print in fluid-tolerant flexible material, keep fragments out of the reservoir and confirm the cap seals without obstructing the pump pickup or hoses.

Fits W123 Series · W123 / S123 / C123

Protective body plug test-fitted in a 123-series jacking point. The creator printed it in ABS with three flex slots and advises rust protection inside the jacking tube before installation. This is a dust and appearance plug only: remove it before using the factory jack, never treat it as a lifting pad, and inspect the jacking point for corrosion before lifting. The source mentions reference number 2018990008, but no exact EPC child-component record was independently recovered, so no OEM number is assigned.

Fits W123 Series · W123 / S123 / C123

Replacement plug-style retaining clip for the windscreen-wiper vent grille. The creator checked the dimensions on a 123-series car and notes that minor sanding may be needed because the design substitutes a plug action for the original push-through clip. Use weather-resistant material, fit without cracking the grille and confirm every clip remains secure through wiper operation and water flow.

Fits W123 Series · W123 / S123 / C123

Protective cap for the windscreen-wiper shaft, explicitly shown on 240D, 300D and 300TD applications. Use UV- and weather-resistant material, verify clearance through the complete wiper sweep and ensure the cap cannot loosen onto the windscreen or cowl.

Fits W123 Series · W123 / S123 / C123

Front tow hook cover for BMW E39 vehicles with pre-facelift bumper (1995 to 2000). *Normal PLA is not suitable for this application. Source specifies 1995-2000 pre-facelift bumper and warns against PLA. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Replacement cap for the windshield-wiper arm retaining nut on BMW E28 and E30. The creator reproduced the current shape from an original part and reports a perfect fit. BMW number 61611370387 is the black covering cap, used on the passenger side of LHD cars and driver side of RHD cars in the creator's application; confirm side, arm style and production date by VIN.

Fits 3 Series · E30 · 5 Series · E28

Replacement clip and glue-in double-stud repair for broken F33 Convertible roof-frame moulding retainers, designed on and physically demonstrated with a 435i F33. The BMW clip file corresponds to superseded 51 76 7 162 587, now 51 76 5 A71 150; the custom glue-in double stud is not separately serviced and no moulding assembly number is assigned. Use heat- and UV-resistant material plus high-strength compatible adhesive, follow the creator's hook orientation, and verify full roof travel, strip retention, drainage and sealing before driving.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Funnel sized for the BMW F30 washer-fluid filler neck and physically shown in the engine bay. Use fluid-, heat- and UV-resistant material and verify full cap, hose, bonnet and washer clearance.

Fits 3 Series · F30 / F31 / F34 / F80

hi this is my custum made for led back cover lights bmw e90 318i valeo lci ligts please use support my paypal is: sezgin9716@hotmail.com thanks :) Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E90 / E91 / E92 / E93

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2

Snug-fitting flat cover for the E30 power-antenna opening. The creator reports it stays in place without extra fasteners; confirm the body opening, weather sealing and retention before road use.

Fits 3 Series · E30

Replacement receptacle for the ball studs on 1999–2004 Grand Cherokee WJ and WG headlight housings. Three receptacles support each lamp while preserving adjustment movement.

Fits Grand Cherokee · WJ / WG

Replacement wing handle for the spare-tire retainer used in 1999–2004 Grand Cherokee WJ and WG cargo areas. The print captures a standard M10 × 1.5 hex nut.

Fits Grand Cherokee · WJ / WG

Bolt-on bracket developed for mounting a three-inch auxiliary light above the front fender of a Grand Cherokee ZJ. The source documents the installed bracket from three angles.

Fits Grand Cherokee · ZJ / ZG

Push-fit center cap modeled for 1993–1998 Grand Cherokee ZJ wheel hubs. The source includes an installed result and recommends PETG with supports.

Fits Grand Cherokee · ZJ / ZG

Strengthened upper clip that retains the Grand Cherokee ZJ headlight reflector to its vertical adjuster. The source covers the full 1993–1998 ZJ range and documents the load-oriented print position.

Fits Grand Cherokee · ZJ / ZG

Threaded replacement hood-height stop measured from the original on a 1993 Grand Cherokee ZJ. The creator installed the part and recommends an under-hood material rather than PLA.

Fits Grand Cherokee · ZJ / ZG

Replacement push button for the exterior door-opening handle on a 1998 Grand Cherokee ZJ.

Fits Grand Cherokee · ZJ / ZG

Multi-piece snap-in center cap modeled for the approximately 55–56 mm wheel opening on a 2004 Jeep Liberty KJ. This entry uses the creator's plain top and excludes the decorative lettered top.

Fits Cherokee / Liberty · KJ / Liberty

Direct replacement windshield-washer nozzle for a 1989 Cherokee XJ, revised with three spray ports and reinforced hose-barb and mounting joints.

Fits Cherokee / Liberty · XJ

Outer bushing that fits a Hi-Lift jack climber rung around the Rampage carrier bolt to suppress rattling. The creator states JK and JL fitment.

Fits Wrangler · JK · Wrangler · JL

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1