Find your next part.

This is a printable replacement for a Subaru Impreza hood support rod end cap - or whatever you want to call the plastic part that fits into the hood slot when the rod is raised. This piece (white piece in picture) broke on our 2016 Impreza and Subaru seems to only sell the entire rod, not just the cap piece, so I decided to take a whack at modeling and printing a new one. I'm new to Fusion 360, so it took a few tries, but this one is working nicely for me. I'm not sure which other Subaru models/years this would work for, but there's not really much to it, so if it looks like the part in the picture, you can give it a shot! The part is pretty close to the original, though I did beef it up a bit in the area where the original one broke. I also set infill at 50% which might be overkill, but it seemed better to overbuild. You'll need to print with supports, and be sure to have your xacto handy to do some somewhat fiddly cleanup. I printed this using Prusament Galaxy Black PLA, mainly because it's all I have on hand, but let's face it, the engine compartment of a Subaru Impreza could use a little glittery bling, right?

Fits Impreza · Fourth generation (GJ/GP)

On my Subaru Forester SG 2005 install is plug and play. I print it in TPU end 2019 , after cleaning looks like new ABS hold only 3 month

Fits Forester · Second generation (SG)

Subaru Forester 1996-2002 CAP-WASHER TANK Original part #86615 I lost my own and print to replace it. There are latches on the inside of the washer cap. And I also made a loop where you can tie a rope so that you don’t lose it again! :) --- Subaru Forester 1996-2002 крышка бочка омывателя. Оригинальный номер #86615 Свою я успешно где-то потерял, придумал замоделить. Внутри крышки защёлки. А также сделал петлю куда можно привязать шнурок чтобы больше её не потерять! :)

Fits Forester · First generation (SF)

This is a an adapter to mount a Yakima Ski Rack to my 2018 Subaru Impreza Stock Crossbars. Did not like the expensive adapters Yakima sells, they didn't seem as secure nor as stable. Print four of these in total, two for each rack. These adapters can snap over the crossbars and be slid into place. When the ski rack is tightened, the mounts grip and do not slide. I printed these in PETG. I did not strength test these, but have not had any problems driving at highway and interstate speeds. Will update with any problems. Might work with Subaru Crosstrek as well, since a lot of parts are interchangeable.

Fits Impreza · Fifth generation (GK/GT)

This is a simple tool for installing your Cam Oil seals flush (I got frustrated with useless install kits that pushed it in too far or not straight) This was for my Subaru Forester 2010 SOHC, it has 45 x 32 x 8.0mm cam oil seals Just tap in with a light rubber mallet, worked great Designed in Tinker CAD, which I am getting the hang of, bit by bit I used random z seam &10% support , comes out easy on PLA+

Fits Forester · Third generation (SH)

To get stability in the middle bottom area, you should bend a sheet metal strip by 90° and fix it in the direction of the rear bumper. take TPU, ABS are not durability

Fits Forester · Second generation (SG)

forester_sf_5_radiator_grill_mount

Fits Forester · First generation (SF)

A printer friendly version of pimaster's [2004 Subaru Forester Bonnet Stay Clip](https://www.thingiverse.com/thing:213626)

Fits Forester · Second generation (SG)

Clip-under cover, front, 56411FA000 Part 4 on this page: http://opposedforces.com/parts/forester/en_s11/type_9/body_equipment_exterior/under_cover_and_exhaust_cover/illustration_1/ Subaru Forester SG '04, April — '05, May '05, March — '06, May '06, April — '07, May '07, March — '07, November Part usage information Europe FORESTER S11 FORESTER S10 IMPREZA G11 IMPREZA G10

Fits Forester · Second generation (SG) · Impreza · First generation (GC/GF/GM) · Impreza · Second generation (GD/GG)

Horncover for Subaru Impreza G3 (2.0D) (60mm Horn)

Fits Impreza · Third generation (GE/GH/GR/GV)

Replacement radio console supplied as a blank template for a custom radio and gauges. The creator also supplies split files for printers that cannot produce the complete piece.

Fits Corvette · Third generation

Replacement windshield-washer reservoir cap designed for a 2011 C-Max.

Fits C-Max · Second generation

Replacement key-fob bezel that helps prevent accidental tailgate-button presses.

Fits Kuga · Second generation

Replacement arm compatible with a GoGen phone holder.

Fits Mondeo · Third generation

Phone holder designed for the newer-model dashboard layout.

Fits Transit · Fifth generation

Hood holder clip supplied as either a snap-in design or an M3 bolt, nut, and washer design.

Fits Fiesta · Fifth generation

Passenger-side fusebox-cover upholstery retaining clip.

Fits Focus · Second generation

Power-outlet cover adapted for a multimedia USB cable, using two screws and separately printed glued latches.

Fits Mustang · Fifth generation

Based on Motorpixiegmibals model - Extend the bottom to fit Tesla Model S and X - Printed in Bambu P1P - Using PLA - Printed in 24m - with Raft

Fits Model X · First generation

This is an adapter to make the trailer hitch socket on the Tesla Model X more accessible. In addition to this adapter, the following items are required: Company Hella 8JA 005 951-001 Company Hella 8JB 005 949-012 Cable 13-pin 2,5mm² 3 cylinder head screws M5x40mm 3 hexagon nuts M5

Fits Model X · First generation

Original Tesla Model X rivets securing the hitch rack plastic panel are not very practical to unlock. This is a redesigned rivet you can lock and unlock with no tools. __Edit__ : Uploaded a v2 which should unlock a bit better. On the photo, there's a print of v1 made with a 0.2mm nozzle, 0.1mm layer height.

Fits Model X · First generation

3D Printable mounting bracket for the Tesla Model X Front License Plate. It is designed to be inserted into the lower grill in the front (in the middle section of the lower grill). The reason it is designed in such a way is because the intended use is to get out of "Fix It" tickets. When you get a "Fix it" ticket for no front license plate. You set this up and slip it on the lower front grill. You show it to the cops and you pop it off once the cop signs your ticket. If you want to secure this to the front grill, there are holes in the bracket where you can add zip-ties to hold it together. Revision History: 10May2018 - Added 3 Files with *_FDM suffix that are meant to be easier for FDM printers to print.

Fits Model X · First generation

Near-replica rear towing-eye cover for AWD/Quattro vehicles.

Fits TT · 8N

Female retainer clip and locking pin for the front mudflaps. The creator specifies horizontal printing with supports, 100% infill, and black PETG.

Fits Model Y · First generation