Find your next part.

Ashtray-slot phone holder for the pre-Puma dashboard.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Land Rover Defender Internal Door Handle

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

This is a defender door's lock escutcheon

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Land Rover Discovery 2 window and heating switch cover. You need to print 4 pins.

Fits Discovery · 1 · Discovery · 2

Defender door card clip

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Land Rover Defender LT77 Gear knob

Fits Defender · 300 Tdi · Defender · Td5

Eight left/right repair rails for broken BMW E36 Coupe and M3 Coupe door-panel attachment areas. The source documents the physical repair and installed door panel. Bond and clamp each section on the correct side, allow full cure, and verify window and latch clearance.

Fits 3 Series · E36

A cup holder that clips to the metal dash of a Series 1-2a.

Fits Series · 1 · Series · 2 · Series · 2A

This is a defender door's lock button housing

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

This is the defender door's sill lock button

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

This is a defender's door card clip mount

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Three alternative inserts for an ashtray or coin-tray opening: a blank panel, a three-switch panel, and a dual socket panel.

Fits Discovery · 1 · Discovery · 2

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +8

It works and fits, but it is sturdier than the original and if you want extra sturdiness, then make it even thicker, because there is still more place for that part. Print the pin as a separate part and glue it together. it will look better, save you time and work better. Please do not re-upload STL or any other mesh version of this project. I upload STEP only, because I want it to be easily editable. Do not poison the internet. For commercial use contact me and I am sure that we can build something cool out of it. Other than that do whatever you like as long as you mention me as the author of the model. Creator reports the replacement fits and works, and supplies separate claw/pin and combined STEP versions. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Cubby-box extension with two cup recesses and a central storage pocket.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Five-piece adapter set for 165 mm midrange speakers and 44 mm tweeters in Euro-spec E46 Coupe and Convertible doors without factory Hi-Fi or Harman Kardon. The creator documents the original mounts, printed adapters, driver assembly and installed sound-deadened doors. Verify speaker, wiring, window and door-trim clearance before fastening.

Fits 3 Series · E46

Land Rover Defender Door Panel Dowel

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

A 65 mm reducing ring for the loose factory cup holder in 2019–2025 Toyota RAV4 models.

Fits RAV4 · 5th Gen

Cupholder-mounted MagSafe phone stand for PDK interiors with the deeper cupholder slot. The creator recommends PLA+ or carbon-fiber PLA and states the design was tested only on the 992.2.

Fits 911 · 992

This is the rear left and right window liner. This requires a larger printer but you can cut it in the slicer and join it afterwards

Fits Defender · 200 Tdi

Replacement drive gear for a failed power-seat motion axis in a 1997 Grand Cherokee ZJ. The creator installed the printed gear after removing the broken original and documents the repaired mechanism.

Fits Grand Cherokee · ZJ / ZG

Custom cup holder that the creator states is made for this vehicle generation and attached with a zip tie. The publication supplies one STL and only a CAD-render source image; it gives no material, print settings, exact mounting location or long-term test evidence. Check container diameter, attachment-point strength and clearances, use cabin-heat-resistant material and secure it so neither the holder nor a drink can obstruct controls or occupants or become loose under braking.

Fits G-Class · W463

Two-piece replacement fuse-box cover with raised fuse-position text, modelled from a damaged original cover.

Fits Land Cruiser · 60 Series

Dashboard mounting bracket for a Garmin navigation unit in the Puma interior.

Fits Defender · Puma