Find your next part.

Trim cover for the upper seat-belt height-adjuster anchor. Source photographs show the printed cover installed over the factory adjuster; it is cosmetic and must not carry belt load. Use tough cabin-heat-resistant material, preserve unobstructed adjuster travel, never cover damage or alter the belt, anchor or mechanism, and confirm the belt retracts, adjusts and locks normally after fitting.

Fits Vito / Viano / V-Class · W639

Replacement pull handle for the sunroof shade. The creator designed it for the CLS C219 and explicitly reports confirmed E-Class fitment; source images show the physical handle installed. No other roof or trim variant is inferred.

Fits E-Class · W211 / S211

Storage tray that installs in place of the factory CD changer. The creator specifies ASA or ABS, four walls, five top and bottom layers, and 13% infill.

Fits E-Class · W211 / S211

Replacement tab for the rear center-console air vent. The author states that it fits this vent position only and that other air-vent locations were not tested; surface finishing and paint may be needed.

Fits E-Class · W211 / S211

Strengthened replacement clip for the glovebox ballpoint-pen holder. The creator explicitly lists W169, W203, W204, W209, W212 and W245 fitment, shows the part installed and recommends ABS for cabin heat; W245 is absent from the live taxonomy. No body, market or production-break split is stated, so compare the original clip and glovebox recess before printing, fit without damaging the lid and confirm the pen and clip cannot detach into the footwell.

Fits A-Class · W169 · C-Class · W203 / S203 / CL203 · C-Class · W204 / S204 / C204 +2

Replacement plastic support panel beneath the wooden centre-console switch trim. The creator reports that the design works but may require sanding. Compare the switch layout and console version before printing, use cabin-heat-resistant material, deburr all openings, and confirm switches, wiring and the selector remain unobstructed.

Fits 190 Series · W201

Replacement cap for a broken cabin-blower control switch, modeled from the original for a 190-series interior. The source provides comparison imagery but no long-term validation details. Compare the switch shaft and detents, use tough cabin-heat-resistant material, and verify every blower position operates and the cap cannot bind against the panel.

Fits 190 Series · W201

Replacement 12-tooth drive pinion demonstrated in an Australian-compliance 1989 560 SEC instrument cluster. The creator printed, fitted and updated the gear profile after road use, and reports continued odometer operation. Fitment is restricted to a matching 12-tooth cluster; do not assume every 126-series speedometer uses it. Support the rotor shaft during press-fitting, preserve end float, have any desoldering performed competently, and verify accurate speed and distance readings before road use.

Fits S-Class · W126 / C126

Modified rear-deck grille for Rockford Fosgate R1525 5.25-inch speakers, derived from the creator's credited earlier grille design. The source specifies ABS or another high-temperature material to avoid cabin-heat deformation. Secure the speaker independently, verify grille retention and keep the installation clear of rear-window visibility and parcel-shelf hardware.

Fits W123 Series · W123 / S123 / C123

Replacement plastic locating pin for the wooden switch panel in the centre console, demonstrated on 240D and 300D cars. The creator provides a central hole for an optional cut-down steel nail bonded with adhesive to reinforce the shaft. Keep metal reinforcement fully encapsulated and clear of wiring, use heat-resistant material, and confirm the panel is retained without stressing the veneer or switches.

Fits W123 Series · W123 / S123 / C123

Replacement door-seal clip measured directly from an original coupé component. The creator tested prototypes in PLA and final parts in ASA/PETG, recommends nylon for durability and specifies horizontal print orientation for strength. Fitment is limited to the coupé body. Compare the original clip, deburr all edges and confirm the seal seats continuously without preventing safe door latching. The source references A0009871015, but no exact independent EPC child-component record was recovered, so no OEM number is assigned.

Fits W123 Series · W123 / S123 / C123

Flexible protective sleeve for wiring passing into a front door. The creator specifies 123-series driver or passenger doors, flexible filament, and an upward slicer orientation for the sealing-lip end. Route the wiring without tension, seat both ends fully, confirm the door closes without pinching the sleeve, and inspect periodically for abrasion or water ingress.

Fits W123 Series · W123 / S123 / C123

Blanking cover for an unused centre-console switch opening. The creator designed it on their own 123-series car and reports a perfect fit; the opening may also be used as the basis for a custom switch or charger. Compare the slot dimensions and console finish, keep clear of wiring and moving controls, and fuse any electrical accessory separately according to its manufacturer instructions.

Fits W123 Series · W123 / S123 / C123

Bolt-on replacement handle for broken manual seat-adjustment levers. The creator explicitly designed and photographed it for both 116-series and 123-series cars, states that it can be used at all four handle positions, and notes that side height adjusters accept one screw while the front adjusters use two. The demonstrated part was printed in PETG, sanded and buffed, then fastened through the surviving metal lever with screws and nuts. Remove only the remains of the failed grip, preserve the original lever, deburr all holes, use secure low-profile hardware, and confirm full adjustment and locking travel before driving.

Fits S-Class · W116 · W123 Series · W123 / S123 / C123

Replacement rocker cap for the electric-window switch. The creator modeled it after a broken original, reports that it fits, and recommends resin printing because ordinary FDM appearance and durability were unsatisfactory. Preserve the switch mechanism and contacts, confirm free return movement and electrical isolation, and stop using the part if it binds or softens in cabin heat.

Fits SL · R107

Replacement 8 mm dashboard screw cap, shown as a loose physical print beside its screw. The source identifies E85 fitment but no separately serviced BMW component number; do not force the cap, and verify colour, diameter and trim retention.

Fits Z4 · E85 / E86

Replacement upper hook bonded to the rear seat-back trim shell. The creator modeled it from a 3D scan of the original F16 component, physically compared the printed replacement with the original, and later corrected the upper section for proper attachment. Mirror the supplied file for the opposite side. Use a heat-resistant, tough cabin-suitable material, verify the hook orientation and seat-back shell geometry before bonding, and keep adhesive and the printed part clear of seat latches, belts, airbags and folding mechanisms.

Fits X6 · F16 / F86

Replacement trim sleeve surrounding the interior door-lock pin. The creator modeled it as a solid, friction-fit alternative to the original slotted piece, physically compared the print with the original and shows it installed in the door top. It corresponds to BMW locking-button cover 51 41 8 408 567, used on front and rear E53 door trims. Print in a UV- and heat-resistant material, compare the sleeve and pin travel with the original, and ensure the lock pin moves freely before use.

Fits X5 · E53

Four one-piece tray variants for fitting one or two Baseus Simple Mini3 15 W wireless chargers in the 2023 X1 center-console shelf: full and short versions for either a single charger or a pair. The creator dimensioned the tray to the vehicle, physically printed it in PETG and 85A TPU, shows installed trays with phones, and reports testing with multiple iPhone 6.1-inch and Galaxy S models. Chargers insert from below and their cables route to the right-side USB-C ports. This is aftermarket accessory geometry, so no console or charging-module parent number is assigned. Do not use PLA; confirm cable strain relief, charging temperature, phone retention and unobstructed controls before driving.

Fits X1 · U11

Just glue the pin to the plate and add some velcro and you are done! The creator tags F10/F11 and supplies physical photographs of the printed two-piece lock. Glue the pin to the plate, add adhesive hook-and-loop material, and confirm the mat cannot interfere with pedal travel. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

the bmw e60 vents were very floppy and i went to see what was wrong and some how that small piece in my vent was the whole reason my vents wernt standing straight and working i found one of them so i could design these pieces 1-1 as the original i printed this in bambu black carbon fibre fillament Measured one-to-one from the original clip to restore a loose rear center vent. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Cable holder for 7mm hole. Printed without brim. Creator documents the printed holder on an E61 door harness and specifies a 7 mm mounting hole. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

This part is a small storage cubby for use in place of the broken center console ash tray for BMW E39. The bottom clip of the ash tray holder is commonly broken on E39 models and cannot be fixed without replacing with a working center console trim piece, which can be hard to find in good condition. The part includes a cutout for the illumination strip so the cubby is illuminated at night. Fitment is very tight to avoid the use of adhesives. Carefully press in with a bit of force and it will fit as shown in the photos. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Print without support, use flexible material (TPU, PBT etc.) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39