Find your next part.

Just glue the pin to the plate and add some velcro and you are done! The creator tags F10/F11 and supplies physical photographs of the printed two-piece lock. Glue the pin to the plate, add adhesive hook-and-loop material, and confirm the mat cannot interfere with pedal travel. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

the bmw e60 vents were very floppy and i went to see what was wrong and some how that small piece in my vent was the whole reason my vents wernt standing straight and working i found one of them so i could design these pieces 1-1 as the original i printed this in bambu black carbon fibre fillament Measured one-to-one from the original clip to restore a loose rear center vent. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Cable holder for 7mm hole. Printed without brim. Creator documents the printed holder on an E61 door harness and specifies a 7 mm mounting hole. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

This part is a small storage cubby for use in place of the broken center console ash tray for BMW E39. The bottom clip of the ash tray holder is commonly broken on E39 models and cannot be fixed without replacing with a working center console trim piece, which can be hard to find in good condition. The part includes a cutout for the illumination strip so the cubby is illuminated at night. Fitment is very tight to avoid the use of adhesives. Carefully press in with a bit of force and it will fit as shown in the photos. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Print without support, use flexible material (TPU, PBT etc.) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

I designed it in a blender. Fits cars: BMW X5 E53, 1999-2007 BMW E39 series 5, 1995-2005 I printed it on cr-10 with .4 nozzle and .2 layer height Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · X5 · E53

Replacement roof hook for the accessory rear roller sunshade used on BMW E28, E30 and E34. It was reproduced from an original part and physically installed. BMW accessory number 82129413178 identifies the discontinued black two-piece roof-hook set; 82129413177 is the different white lower-hook style. Confirm headliner mounting, accessory configuration and color before fitting.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement center retaining clip for the sun visor of a BMW E12 520. The creator physically fitted the part and recommends PETG, ASA, ABS or another cabin-heat-resistant material; PLA can deform in summer. BMW catalogs identify the equivalent ivory holder as 51161870863, superseding 51161820684; the photographed black print is a user-selected reproduction color, not an OEM color claim. Production date and trim variants can differ, so compare the two-hole base and visor-rod diameter before fitting.

Fits 5 Series · E12

I created this for my 2011 E91, but it may fit others. Just pull the other parts out of the vent and snap this one on. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

This is a nice update for us with older E90 BMW's This will allow you to mount a universal Inbay wireless charger. This seems to work well and looks like a factory addition. It will take place of the front pocket in the console or the ashtray if it was equipped. This bracket will mount directly inplace of the old insert. Powering up the device: I did not have the ashtray so I was able to wire this into the power of the usb in th back of the console. you can access this easily by removing the rear vent panel. you can also pull out the plastic rear vent tubing with a little force to more room. You will tap into the Brown/ Ground and the Red/ +12V going to the usb in the rear console. LED Light: As an option I have added some holes for the LED light on the side of the charger. you will need to source a thin fiber optic cable and use the included plastic insert to fit the bigger hole. you wi Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

So I was looking for a fitting cupholder for my BMW E90 tray and couldn't find one which wasn't too big. This one fits to your BMW E90 without the big navi and without the iDrive knob. I made 3 versions which can fit 250ml, 330ml or 500ml cans (Germany/EU). With the big one, the walls might get too thin, read below. It fits very good to the tray, I use it everyday. This was designed to be printed with PLA, if you use ABS you might upscale it. Also, you can print it on the flat surface with my tag without supports. If you like the design, leave a tip :) *** Update 27.06.20 Someone requested a wider hole (currently 57mm) for norwegian 500ml cans. Uploaded another version with 66mm. Walls get very thin and cut, NO guarantee for good results as I won't try it! *** Update 11.07.20 Was shopping a german/EU 330ml can and couldn't fit it. So I made the hole slightly wider (59mm) to fit these. Ha Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Doorstep broken clip holder part replacement. Designed to have large surface area for glue to properly hold it. I have also designed the clip, check my other designs. Print with 5+ walls vertically oriented , and glue it on the bracket with 2 component glue for best results. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Inserts into the stock E46 ashtray, should be friction fit. I included all of my files, with the following features: .stl with the holder cutouts intended for my own use, Hörmann Garage Door Opener, a ISO/IEC 7810 ID1 cutout and a generic one to use the remaining space .step without cutouts for your own modifications .f3d so you can look at my bad modelling skills and also make your own modifications I would recommend to print this in ABS, PETG may be fine but PLA will 100% shrink if your car heats up. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

We did 6 different version to get it in the angle that it faces the driver. We had a tight fit so it did not need any mounting to the dash, but maybe some glue or other adhesive wouldn't hurt. Printed flat down on the surface, with ABS+ to resist the summer heat in the car. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Repair bushing for the E46 and E53 window regulator, physically assembled and load-tested by the creator with an M6 thread. The creator warns that ordinary PLA failed in summer heat. Use heat-resistant automotive material, dry-fit before fastening, and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · X5 · E53

Replacement clip for the door-sill trim. The creator installed several copies and reports that they hold securely. Align the clip carefully during installation so it does not break while being pressed into place. Use cabin-heat-resistant material, dry-fit the part, and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

These are speaker adapter mounts for BMW E46 front doors. There is a mount for both the tweeter and woofer. The mounts are designed for a JL Audio C3-525 component set but I have included generic .stp files for the mounts to adapt the design for your speakers. The woofers are screwed into the printed adapter rings and then the factory mounting screws are used to fix them to the door card. The tweeters clip into the mount with a twist and are held with integrated springs. The tweeter mounts also re-use the factory screws to hold them to the door cards. Left and right are exactly the same and there is no need to mirror the mounts. These fit perfectly and I have had no issues after a month of i Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

If you don't use the flashlight in your e46 BMW glovebox, here is a nice USB port adaptor that will plug right into the dash and give you two switched ports! I removed the center of the flashlight receptacle with a screwdriver and removed the pins, which are reused in the new adapter. Print both pieces, then wire two of these buck converters with 18AWG wire. There is not a lot of space, so you need to be delicate. Pin closest the the edge is negative. Solder the lead wires to the pins before inserting from the bottom - be careful not to insert too far. Push the assembled converter into the receptacle, push the female connector housing onto the back, plug in the wire from the car and re-inser Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

Two-gauge replacement for the BMW E36 centre vent. Only the physically printed and installed double-52 mm variant is retained from the source; its other untested variants are excluded. Confirm gauge depth, wiring, visibility and remaining demist airflow.

Fits 3 Series · E36

Replacement sunroof-motor cover for BMW E36 Coupe, with separate switch-cutout and plain versions plus the source 3MF. The source shows a finished print and physical installation. Use cabin-heat-resistant material and verify switch, motor, headliner and retaining-clip clearance.

Fits 3 Series · E36

Replacement interior door-trim clip traced from the original and modified for strength. The source physically compares the printed clip with the original. Test one clip for panel alignment and removal before replacing the full set.

Fits 3 Series · E36

Replacement centre-vent insert measured from a BMW E36 323ti Compact and physically installed with a 52 mm gauge. It sacrifices vent airflow at that position; use cabin-heat-resistant material and verify gauge, wiring and dashboard clearance.

Fits 3 Series · E36

Replacement knob specifically for the late-model E30 manual sunroof crank, shown physically installed. Use cabin-heat-resistant material and verify that the crank turns and folds freely.

Fits 3 Series · E30

Replacement E30 electric window-lifter spacer for mechanisms through April 1988, reproduced from the original and physically installed. BMWFans confirms spacer 51331919541; power-window mechanisms only.

Fits 3 Series · E30