Find your next part.

Land Rover Discovery 2 horn button cover.

Fits Discovery · 2

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.

Fits Wrangler · TJ

This is a defender's seat lever knob

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Clip Front Seat Belt Retainer For Land Rover Defender

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Replacement interior door-handle trim bezel for BMW E30, E24, E28 and E23, physically printed and fitted. BMWFans confirms cover 51211876043. Print in a UV- and cabin-heat-resistant material.

Fits 3 Series · E30 · 5 Series · E28 · 6 Series · E24 +1

Multi-part dashboard housing, frame, gauge mount, button, adaptor, and support bracket for the BinOwl onboard-computer installation.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5

Replacement blanking button for an unused dashboard switch position. Two model variants are included

Fits Discovery · 1

Adapter plate that replaces the obsolete factory phone cradle while reusing its original dashboard bracket and screws, with variants for a Brodit MoveClip mounting pattern and alternate screen position. Source photographs show the bracket, plate and phones installed. Match the equipped cradle and screw lengths, use cabin-heat-resistant material, and confirm the device cannot obscure instruments, controls, airbags or the driver view.

Fits Vito / Viano / V-Class · W639

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

Fits A-Class · W177

Land Rover Discovery 1/2 window switch bezel. You need to print 4 pins

Fits Discovery · 1 · Discovery · 2

Replacement slider for the factory BMW wireless-charging cradle that increases usable phone length to approximately 168 mm. The creator documents F2x, F3x, F8x, and I01 cradle compatibility and shows the printed part installed and measured. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material; verify latch engagement, charging operation, and secure phone retention before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +2

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Replacement electric sunroof latch.

Fits 924 · 924 · 944 · 944

Replacement center-console assembly laid out for a double-DIN radio installation.

Fits 924 · 924

Two-piece dual cup holder designed to insert into the centre-console cupholder while preserving access to the 12-volt socket, armrest and selector. The source supplies cup and stand STLs plus a CAD image but no container-size or crash-retention test. Use cabin-heat-resistant material, check console and selector clearance and test only with cold, closed containers before road use; confirm the assembly cannot detach or spill into controls under braking.

Fits C-Class · W203 / S203 / CL203

Replacement retaining hook for the roller sunshade in a rear door. The creator modeled it for the fourth-generation X5, shows the printed clip next to the original, and documents it installed and holding the shade. The printed hook is intentionally slightly shorter than the original. BMW component 51 35 7 479 511 is catalogued for the G05 X5 and G06 X6 rear-door shade application, so both evidence-backed generations are linked. Fitment requires the rear side-window roller sunblind equipment; confirm door trim, shade and mounting geometry by VIN. Print in a heat-resistant automotive material and test smooth release and secure retention before road use.

Fits X5 · G05 / F95 · X6 · G06 / F96

Replacement plus/minus volume rocker modeled after the creator's broken multifunction steering-wheel button and physically shown loose and installed. The creator documents direct fitment to X3 E83 and X5 E53. BMW services the surrounding switch assembly rather than this printed child button separately, so no parent assembly number is assigned. Use a durable heat-resistant material, preserve free button travel, and verify all steering-wheel controls operate without sticking before driving.

Fits X3 · E83 · X5 · E53

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Fits Defender · 300 Tdi · Defender · Td5

Two headlining fastener sizes for a 110.

Fits Defender · Td5

Repair set for later window-regulator motor assemblies, including gear-coupler and roller options. Some versions require drilling and tapping the original steel hub or roller shaft

Fits Discovery · 1

This is a replacement part for the BMW 5 Series Touring (F11). It is the sliding clip ("leash" or "dog") located in the D-pillar track that automatically raises and lowers the rear cargo blind (luggage cover) when the trunk is opened. OEM Part Number: 51437232775 Tested on: BMW F11 520d Touring IMPORTANT INSTRUCTIONS 1. FUNCTION: This part slides inside the track of the rear pillar. It is crucial for the automatic retraction of the luggage cover. 2. LEFT vs RIGHT Side: The uploaded file is for the LEFT side. If you need the RIGHT side, simply use the "Mirror" function (along X-axis) in your slicer software. 3. MATERIAL RECOMMENDATION: Because this part moves in a track and bears weight, I strongly recommend printing with NYLON (PA). - Nylon provides the necessary low friction and high durability. - ABS/ASA might work but will wear out faster. - PLA is NOT recommended. 4. PRINT SETTINGS: - Infill: 100% (Solid) for maximum strength. - Orientation: Print in an orientation that maximizes layer adhesion strength for the pulling force. Designed from scratch as a cost-effective alternative to the expensive OEM repair kit. Creator-tested on an F11 520d Touring. The supplied file is the left sliding coupling; mirror on X for the right side. BMWFans identifies genuine BMW 51437232775 as Coupling, left, produced from 2010-06 for F11/F11 LCI European applications including LHD and RHD. Use nylon where possible, not PLA, and verify smooth movement before loading the blind. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

The center console catch broke in my BMW E61. I've removed the remaining plastic and printed this piece. Attach with two screws and it works perfectly again. Print with 100% infill for extra strength. Creator reports a perfect working repair attached with two screws; photographs show the installed E61 console lid. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Replacement ventilator control knob modelled from the original component.

Fits Series · 2

Dashboard bracket for a 9.3-inch portable CarPlay display. The upper edge tucks beneath the dashboard trim while taped feet support the screen

Fits Discovery · 3 · Discovery · 4