Find your next part.

Two-piece replacement mounting set for the vacuum actuator on top of the factory air-conditioning box. It adapts the installation to a Dorman 604047 vacuum actuator; installation requires reworking the actuator arm with a screw and nut, trimming the replacement actuator to fit, and using two M3×6 and two M3×8 screws. Verified fitment is 1965–1968 Ford Galaxie.

Fits Galaxie · Fifth generation

Door-mounted spacer ring for installing a 165 mm (6.5-inch) aftermarket speaker in the front door speaker location of the Nissan March/Micra K11 (1992–2002). The ring increases clearance for a less-shallow speaker and provides the vehicle-side and speaker-side mounting interfaces; the speaker, wiring, fasteners, locknuts, and shims are separate components. Verify the exact speaker diameter, mounting depth, hole alignment, window and trim clearance, wiring routing, fastening, and vibration isolation before installation.

Fits March · K11

Replacement center-console armrest USB pass-through cover that replaces the factory USB socket surround and lets a Lightning cable pass through while routing the cable to an under-armrest interface. Includes the printed cover only; the cable, tie, and any electronics are separate. Fitment is verified for the Nissan GT-R R35 (2007-2025). Creator guidance specifies Nylon CF and recommends against PLA for hot vehicle interiors; verify the connector, cable tie, armrest opening, and clearances before installation.

Fits Nissan GT-R · R35

Replacement cabin-light housing for the overhead interior lamp opening of the Nissan/Datsun 720 pickup, generation 2730 (1979-1986). The single printed piece provides the perimeter clips, mounting holes, and central lamp recess. The lamp, lens, wiring, and fasteners are not included; verify the roof opening, lamp hardware, clip engagement, clearance, and retention before installation.

Fits Datsun Truck/Navara/Frontier/NP300 · 720

Replacement lower dashboard air vent for Nissan Primera P10 (1990–1996), intended to restore the under-dash HVAC outlet. The source-authored 3MF contains the vent geometry as one mesh; installation and fitment should be verified against the original vehicle opening.

Fits Primera · P10

Replacement dashboard air-vent insert with a 52 mm round gauge opening for the Nissan March/Micra K11. It replaces a side dashboard vent and provides a factory-style mounting location for one 52 mm gauge. The source set includes standard and mirrored STL variants for handed installation; the gauge, vehicle, and non-printed hardware are not included. Verify vent-opening geometry, side/orientation, gauge clearance, retention, and cabin-temperature material suitability before installation.

Fits March · K11

Full-size dashboard side-vent trim panel for the 1978–1983 Nissan Fairlady Z / Datsun 280ZX S130. The single-piece geometry forms the vent surround/trim shell with vent openings and integral mounting posts. The creator recommends 3–4 wall layers for rigidity and ABS, ASA, or PC for cabin heat; verify side orientation, retention, and fit before installation.

Fits Fairlady Z / Datsun Z · S130

Replacement rear-window latch arm for the Nissan D21 King Cab sliding rear-window assembly. Restores the latch retaining function at the rear window; the supplied model is one printed arm, while the window assembly and installation hardware are not included. Print in PETG with supports as specified, and verify the window variant, arm and fastener interface, clearances, and secure retention before use.

Fits Datsun Truck/Navara/Frontier/NP300 · D21

Replacement climate-control knob for the dashboard air-conditioning and heater panel in the first-generation Nissan X-Trail T30 (2000–2007). The knob operates one of the panel controls and includes the source geometry for the shaft interface and position-indicator light slot. Includes one knob; verify the panel variant, shaft engagement, rotation range, indicator alignment, and secure retention before installation. PETG or ABS is recommended for cabin heat resistance.

Fits X-Trail · T30

Replacement clip for attaching the rear parcel shelf to the rear locators on the backs of the rear seats of the Nissan X-Trail T30 (2000-2007). The printed component restores the clip interface; verify seat-back locator geometry, orientation, fit, retention, and clearance before installation. Print in PETG or ABS for improved resistance to cabin heat and confirm secure retention before use.

Fits X-Trail · T30

Two-piece replacement clip assembly for the rear parcel shelf, retaining the shelf at the tailgate trim. Includes the clip body and retaining pin as separate printed components. Verified fitment is Nissan Juke F15 (generation 2748); vehicle and any non-printed hardware are not included. Verify dimensions, material suitability, seating, and retention before use.

Fits Juke · F15

Two-piece dashboard navigation-device holder for the Nissan NV200 M20. The holder seats in the opening on top of the dashboard, supports a TomTom Go5200 or compatible suction-cup device up to 60 mm, routes the power cable through provided openings, and is retained with double-sided tape. Includes the main holder and top cover; tape, navigation device, and other hardware are separate. PETG or ASA is recommended for cabin heat exposure.

Fits Nissan NV200 · M20

Replacement translucent insert for the broken internal section of a manual/standard heater-control knob. Fits the standard heater-control panel represented by the 2003 application within Nissan X-Trail T30 generation 2903; it is not intended for climate-control panels. The insert restores the knob shaft interface and light-transmitting inner piece. Clean and fit carefully: the documented test fit did not seat fully, and forcing the insert can damage the shaft.

Fits X-Trail · T30

Full-size replacement pod for the dashboard vent opening, mounting below the dash and accepting either a 52 mm or 60 mm gauge. The packet includes the standard base, mirrored base, 52 mm insert, and 60 mm V2 insert; two M4x30 bolts and two M4 nuts are required separately. The design is intended as a reversible replacement without cutting or drilling. PETG or ABS are engineering-inferred for cabin heat resistance; verify gauge fit, retention, clearances, and print strength before driving.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Full-size replacement clips for the radio-console/bezel mounting interface. The set includes single-clip and multi-pack variants for Nissan 180SX RS13/RPS13 and Silvia S13 applications represented by the selected catalog generations; the clips restore retention of the radio-console bezel when original clips are missing or broken. PETG is recommended for vehicle-cabin use, while ABS was used for the earlier prints.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Organizer tray for the small front console tray ahead of the shift lever in 2014–2020 second-generation Rogue vehicles. It fits over the rubber tray liner, preserves access to the lighter/power socket and USB-A port, and adds storage sections, pen slots, and a coin slot. Supports are required; PETG or another heat-resistant material is recommended for vehicle-cabin temperatures.

Fits X-Trail / Rogue · T32

Left- and right-side replacement support clips for the rear parcel shelf (boot privacy cover). The clips slot into the existing side recesses and support the cover, restoring its resting support on 2002–2010 Nissan March K12 / Micra K12 hatchbacks. Print in PETG for hot-car resistance; PLA is not suitable for this application.

Fits March · K12

Two-component replacement set for the rear quarter-window regulator mechanism on the 2006 convertible application represented by Nissan March K12 generation 2767. The set includes the main mechanism component and an outside component intended to restore rear-window extension operation; verify side, mating interfaces, dimensions, hardware, clearances, and print-material suitability before installation.

Fits March · K12

3D-printable holder for a Samsung Galaxy Note 9. The printed rail mounts between the radio and dashboard/vent area and supports the phone in front of the center vents. Verified fitment covers 2012-2016 Impreza and 2013-2017 Crosstrek vehicles. The printed holder is the modeled component; the phone and any non-printed mounting hardware are not included.

Fits Impreza · Fourth generation (GJ/GP) · XV / Crosstrek · First generation (GP)

Clip-on dashboard vent mount for a Garmin GPS/navigation unit in the center vents of the 2015 Subaru Outback (fifth generation, BS). The flexible clip straddles the emergency-flasher button area while preserving access to the vents and can be moved between the two center vents; the updated version has reduced pivot range compared with the original clip and is intended to print vertically with tree supports. The vehicle and GPS device are not included.

Fits Outback · Fifth generation (BS)

Full-size cup holder for the dashboard ashtray/blanking-panel opening on a 1997 Subaru Sambar KS4. It provides a 66 mm opening for cans and, with the removable filler washer removed, approximately 71 mm clearance for larger cups or bottles while clearing the manual gear lever. The model includes the cup-holder body and removable filler washer; confirm the dash opening, shift-lever clearance, retention, and print strength before installation.

Fits Sambar · Fifth generation (KS3/KS4/KV3/KV4)

Three-gauge dashboard mount for the center dash lid of the 2009 Forester. The mount provides three instrument-gauge openings, uses a drilling template to locate the mounting holes, and attaches with four M4 screws. The selected files include the current pod body and the drilling-template component; gauge diameter and hardware supply were not verified.

Fits Forester · Third generation (SH)

Two alternative full-size phone-mount variants for the center-console coin pocket of the 2018 Subaru Outback fifth generation (BS). One variant uses a 1.25-inch slot interface and the other provides a flat face for an adhesive-backed mount. Printed parts only; phone, adhesive mount, and mounting hardware are not included. Verify pocket interface, device clearance, retention, cable routing, and unobstructed visibility before driving.

Fits Outback · Fifth generation (BS)

Replacement lower instrument-panel cover that fills the factory switch/blanking-panel opening and restores the retaining features of the original cover. Verified fitment is the first-generation Subaru Impreza GC/GF/GM and first-generation Forester SF, corresponding to OEM 66813FA000; verify the dashboard variant and retention before installation.

Fits Forester · First generation (SF) · Impreza · First generation (GC/GF/GM)