Find your next part.

Two-piece cup holder that mounts with the existing screws after removal of the ashtray-delete rubber liner while retaining access to the storage compartment.

Fits 911 · 996

Closeout panel for the center-console delete opening.

Fits 911 · 996

Phone mount that fits between the side trim of the PCM and is sized for a Google Pixel 5 in a silicone case.

Fits 911 · 997

Replacement tensioner for the factory cupholder. The friction-fit design can function if the original small spring is missing.

Fits 911 · 997

Cupholder installed in the bin between the rear seats and secured by the lower-seat-squab nut. Includes the required nut cover plus optional narrow-cup insert and flexible liner.

Fits 911 · 991

Phone holder for the shared dashboard cupholder slot; this version fits the 69 mm-wide slot and permits a USB charging connection.

Fits 911 · 996

Replacement ramp/clip that pushes down the sunroof wind deflector. The creator fitted the revised design and reported that it works correctly.

Fits 911 · 964

Organizer for the cubby beneath the climate controls, installed by sliding it into the opening from the side.

Fits Macan · XAB Electric

Three-part MagSafe phone holder that clips near the glove-box compartment on left-hand-drive interiors. Its position keeps the holder away from the gear lever and leather trim. It accepts a 46 mm-inner/54 mm-outer MagSafe-style magnet ring and the printed parts are joined with super glue.

Fits 911 · 991 · Boxster · 981 · Boxster · 982 (718 Boxster) +2

Extended ball-socket connector for the exterior door-handle linkage, designed to add adjustment when the lever must be pulled too far or is difficult to reconnect. It uses an extra M5 nut; the creator prints it open-slot side up without supports at 0.2 mm layers and about 15% infill.

Fits 924 · 924

Replacement for the upper square CD-case storage unit in the dashboard, with a top cable-routing port for a USB/Bluetooth module. The creator printed it in resin and reports good fit.

Fits 911 · 996 · Boxster · 986

Left and right interior door-handle shells that convert the 997 door release to a GT3-style fabric pull strap. The archive includes a combined pair and strengthened separate left/right versions.

Fits 911 · 997

Replacement hanger for a rear-door shade. The creator designed it for the 955/957 and notes that it leaves some visual gaps because it does not perfectly follow the door-trim shape, but remains functional; mirror the model for the opposite side.

Fits Cayenne · E1 (955 / 957)

Cup-holder mount for an Apple MagSafe second-generation 25 W charging puck with braided cable. The creator reports fit with an iPhone 16 Pro Max in a silicone case.

Fits Taycan · J1

Replacement finger plate for an early interior door-release handle, modeled after degraded original trim during an upholstery restoration. The creator printed it in ABS for optional acetone smoothing and says PLA should also work.

Fits 944 · 944

Friction-fit tray variants create a second storage level in the seven-inch-deep center-armrest compartment: plain, tissue-box passthrough, and honeycomb versions, plus a STEP stencil for cutting surface liners. The installed tray sits just above five inches from the bottom, leaving room below for a cube tissue box; the creator had not test-printed the honeycomb variant.

Fits Macan · XAB Electric

Left- and right-side frames for fitting nearly any 4x6 speaker behind the factory HiFi grilles while retaining the stock grille appearance.

Fits 911 · 993

Two-piece glove-box CD-holder replacement that mounts two USB ports and provides a pull-out tray for SIM-card access. It assembles with three M3 screws; the updated drawer includes a retaining screw.

Fits 911 · 997

Two-piece platform for mounting an Apple MagSafe USB-C adapter in the 12 V smoker-package compartment below the shifter. The creator calls for a low-profile USB-C 12 V car adapter, automotive trim tape, and glue or epoxy for PLA.

Fits Macan · 95B

Round push-in cover for an interior-trim screw opening, with the opening enlarged by the creator for the larger screws used in their installation.

Fits 944 · 944

Replacement front speaker grille for late-model 944 cars, modeled around Tref67's speaker spacer after the creator found both pieces missing.

Fits 944 · 944

Replacement end cap, catalogued as a sleeve, for the 914-6 manual-throttle rod. The creator recreated it from broken pieces of the original part and old-stock photographs.

Fits 914 · 914

Replacement set for the heater-panel slider levers, supplied as separate upper and lower STL models.

Fits 924 · 924

Clamp that adapts the creator-linked Amazon phone holder to mount on the side of the center console instead of an air vent.

Fits Taycan · J1