Find your next part.

Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.

Fits 911 · 996 · Boxster · 986

Ashtray-mounted phone stand with a USB cable pass-through for an adhesive magnetic charging puck, designed by Trogdor4Ever for the Cayenne 958 center console. The creator printed it in PLA+ and added neoprene foam to the lower corners for a snugger fit.

Fits Cayenne · E2 (958)

Printable lining for a center-console-delete conversion, supplied as a full model or front/rear split for a Prusa Mk3S-size bed, plus a cover plate. The creator recommends PETG, instructs removal of the orange bracket tabs for mounting, and leaves room to upholster the part.

Fits Boxster · 986

Center-console phone mount based on the creator's 3D scan, with versions for iSetchi and Apple MagSafe chargers. The creator reports months of in-car use and says the Apple charger must be attached with double-sided tape or glue.

Fits Taycan · J1

Three-part clip-in center-console coin tray that replaces the ashtray. The creator directs users to slide the parts together, glue the seams, and apply fabric tape at the sides to improve fit and reduce rattles.

Fits 944 · 944

One-piece phone-holder mount for the stock stereo with an approximately 17 mm ball. The creator says it worked with an existing holder and used foam tape beneath the ball to reduce bounce.

Fits Boxster · 986

Vent-wall clamp with an integrated one-inch ball for accessory or phone-mount arms. It expands against the vent walls with two M5 x 18 mm tensioning screws and uses 1/16-inch rubber sheet for grip and trim protection.

Fits Panamera · G1 (970)

Split-ring cap for the upper HVAC blend-door post, installed through the front-luggage-compartment access opening and secured with a small dab of superglue while keeping adhesive off the slotted plastic bearing.

Fits Boxster · 986

Clip-on base for the left edge of the center console that carries an Apple MagSafe charging puck or another magnetic phone holder.

Fits Taycan · J1

Replacement collar stop for the hand-throttle rod, upgraded with two M3 set-screw holes that must be tapped after printing.

Fits 911 · Original (901/911)

Right-rear guide that receives the electric sunroof lifting arm and raises the roof. The creator reports that right and left guides restored operation on a 1984 car and says the opposite side can be produced by mirroring this model.

Fits 944 · 944

Two-piece center-console cupholder replacement designed 1 mm smaller than the stock console to allow vinyl wrapping. The creator plastic-welded the pieces, wrapped the assembly in vinyl, and supplied printable inserts plus a logo stencil.

Fits 944 · 944

Removable dual cup-holder assembly whose bracket wedges between the center dashboard and upper center console. The cup holders can be stored in the armrest when not in use.

Fits Boxster · 986

Center-console tray remix for an iPhone 13 Pro and Anker 15W PowerWave Alloy charging pad, with added phone-positioning blocks and a lower cutout to clear the flip-up cover. It installs after removing the factory rubber liner.

Fits 911 · 991 · Boxster · 981 · Cayman · 981

Five snap-in inserts for the dashboard vent openings that hold recovered vinyl around the holes without glue. The creator says they snap into place and prints them in ABS.

Fits 944 · 944

Two-piece iPhone 12 Pro Max support that replaces the CD-storage function while retaining the original surround; the two printed modules assemble with three M3 x 10 screws.

Fits Boxster · 986

Replacement retaining pin and small gear for the dashboard cup-holder mechanism. The creator thickened the pin for easier printing, increased the gear height for better mesh, and used an 18-gauge brad nail as the pivot. The parts were printed in PETG after PLA softened in a hot car.

Fits Boxster · 987 · Cayman · 987

Replacement flap for the fresh-air blower housing. The creator used a 4 mm foam-rubber seal and PETG for the heat encountered during cabin heating.

Fits 911 · G Model

Replacement blower-intake grille offered as an integrated printable-mesh cover or an open frame for a separate filter or aluminum mesh.

Fits 944 · 944

Replacement for disintegrating heater-panel lever knobs. The single arrowless design presses onto and can be removed from the heater-control levers; it intentionally omits the faint side arrows found on two originals.

Fits 924 · 924

Adapters for 4-inch door and rear midrange drivers plus a two-piece Dynaudio MD-102 tweeter mount. The source covers Dayton Audio RS100/RS100P and Dynaudio E430 midranges; the tweeter mount requires Burmester grilles or modified Bose/SPP grilles and its two pieces are bonded before installation.

Fits 911 · 991

Headliner-mounted radar-detector bracket secured beneath the passenger visor support, with tie-wrap or hook-and-loop attachment points for the detector.

Fits Cayman · 987

Replacement mounting bracket for the interior door storage pocket, modeled for the creator's 1974 911.

Fits 911 · G Model

Left- and right-side repair tabs for broken pollen-filter covers. Replacement variants are for missing original tab pieces; over-top variants wrap available broken pieces or reinforce intact tabs before being glued in place.

Fits 911 · 993