Find your next part.

Replacement covers for the interior door-handle screw openings.

Fits 159 · Tipo 939 · Brera · Tipo 939 · Spider · Tipo 939

Adjustable phone holder designed and measured on a 2018 vehicle, with 13 mm and 16 mm frame variants. The creator recommends PETG after a PLA version deformed in a hot parked car.

Fits Giulia · Tipo 952

Driver- and passenger-side belt guides that fit between the adjustable headrest and seat for inertia-reel belts. The holes accept the original rubber grommets.

Fits Spider · Series 2 (Tipo 105 / 115)

Strengthened replacement bezel that snaps onto the heated-seat control knob. The creator notes that the seat opening must be enlarged slightly for this reinforced version.

Fits 159 · Tipo 939

Replacement clip-in latch for the overhead sunglasses holder. The creator developed it through several fitting iterations and specifies ABS or nylon for cabin heat.

Fits 159 · Tipo 939

Two center-armrest storage tray variants: plain and with coin compartments. The creator recommends adding double-sided rubber inside to stop objects sliding.

Fits Stelvio · Tipo 949

Prototype dashboard frame for fitting a Chinese double-DIN radio.

Fits 147 · Tipo 937 · GT · Tipo 937

Two-piece folding grocery holder designed by Carlos Solis for the Giulia trunk. It bolts to the factory mounting location, folds out of the way, and the creator printed it in PETG for heat resistance.

Fits Giulia · Tipo 952

Left and right parcel-shelf supports designed by profpylons for the Brera. The creator printed them in nylon at 0.15 mm with supports and notes that a nozzle smaller than 0.4 mm may improve the thin features.

Fits Brera · Tipo 939

Replacement sun-visor retaining clip designed by Elek Gábor for the 147. The creator identifies original part number 735344980 and specifies ABS, supports, 0.2 mm layers, 100% infill, and side-surface orientation.

Fits 147 · Tipo 937

Replacement retaining pin designed by Mikael Tonialini for the luggage cover of a 156 Sportwagon. The creator recommends 100% infill and removing the central print support after printing.

Fits 156 · Tipo 932

Replacement cover and mounting adapter designed by Bob Gildoff after the retaining teeth failed on the door tweeters of his 1997 Spider. The creator printed both at 0.10 mm, with supports everywhere for the adapter and build-plate supports for the cover.

Fits Spider · Tipo 916

Phone holder designed by Varsa for a 156 and mounted using a bicycle-style clamp.

Fits 156 · Tipo 932

Cup holder adapted by elec2rak to fit the side door panel of a 156, using the approximately 2 cm door-pocket gap. The creator specifies supports and 5% infill.

Fits 156 · Tipo 932

Remix of RomainCNC's magnetic phone-holder base for the central console, adding a ball for swivel holders. V1 has a 16 mm ball and V2 a 16.5 mm ball. The creator specifies ABS because PLA can deform in a sun-heated car.

Fits MiTo · Tipo 955

Replacement clip for the sunroof mechanism. The creator reports a successful test on one car and specifies PLA, a 0.8 mm nozzle, and 100% infill.

Fits GTV · Alfetta GT / GTV / GTV6 (Tipo 116)

It fits in front of the ignition-switch, designed for the eezee power switch panel so it has a mounting surface of 68x115 mm and mirrored version for RHD vehicles

Fits Range Rover · L322

Three-piece organizer and lid system for the center-console storage compartment. The preserved author package names the main organizer and lid geometry for W177, and four author photographs show the parts installed and in use. No screws or bolts are required; the creator states that the hooks lock into place with light force. Use a cabin-heat-resistant material, test the hook engagement gradually, and verify that the lid and armrest open and close freely without pinching stored items or wiring.

Fits A-Class · W177

Drop-in holder for a MagSafe-compatible wireless charger in the front storage cubby. The creator made and photographed it in a 2020 car and explicitly states W177 fitment. They also suggest same-generation W247, C118, H247 and X247 compatibility but require a visual cubby check; those lines are not among the live generations in this catalog, so only the tested W177 generation is linked. The model is sized around the charger identified on the source page and was designed for an S23 Ultra; verify phone, case, charger and cable clearance before printing. Place the largest face down and use supports. The creator recommends a cabin-heat-resistant material such as PET, PETG, ABS or ASA. Secure the cable and confirm the dock cannot obstruct controls or become loose while driving.

Fits A-Class · W177

Working replacement trim plug for the rear-seat ISOFIX anchor opening, derived by the creator from a 3D scan of the factory cover. The creator states that the scan is not perfect; compare the upholstery opening and verify secure seating. This is only a removable trim cap: it must not obstruct, modify or carry load from the ISOFIX anchor, and it should be removed before attaching a child restraint.

Fits E-Class · W213 / S213 / C238 / A238

Two drop-in console inserts created and physically test-fitted in a GLC: one plain storage cup and one version with a shopping-cart coin slot. The source shows the factory console both open with the inserts fitted and closed over them. Use a cabin-heat-resistant material, confirm the selected insert seats without stressing the factory cupholder, keep loose contents away from controls, and stop use if the print softens, cracks, or binds the console cover.

Fits GLK / GLC · X253 / C253

Replacement clip joining a Rituals fragrance dispenser to the centre ventilation slats in a 2025 facelift V-Class. The creator printed and physically shows it installed, specifies PETG with 0.2 mm layers and 30% infill, and deliberately strengthened the design. Fitment is limited to the facelift centre vent and the matching Rituals dispenser back bars. Confirm both interfaces, insert without bending or scratching the vent slats, preserve airflow and vent adjustment, and remove the accessory if it loosens or obstructs controls or visibility.

Fits Vito / Viano / V-Class · W447

Cupholder-mounted charging dock remixed specifically for the 2014–2022 Vito and tested with an iPhone 12 Pro Max in a thin Pitaka Air case; the creator also states iPhone 13 Pro Max fitment. It requires a small Lightning plug such as the cited 0.5 m Apple cable, with tape used to make the plug snug, and includes a cable channel to the nearby USB port. Print in PETG as recommended, match the exact phone/case/plug and cupholder, secure and route the cable safely, and verify the dock cannot obstruct controls or release the phone under braking.

Fits Vito / Viano / V-Class · W447

Charging dock shaped for the front centre-console cupholder and an iPhone 12 in an Elago silicone case. The creator states exact Vito fitment, recommends ABS or PETG because cabin temperatures can exceed 70 °C, and notes that other cases, phones and cable plugs require geometry changes. Match the cupholder, phone case and charging connector, route the cable without pinching it, use supports as specified, and verify the dock and phone stay retained without obstructing the selector or controls.

Fits Vito / Viano / V-Class · W447