Find your next part.

Two replacement seat-adjustment levers for the opposite seat sides on 126-series interiors. The creator printed both successfully in ABS and emphasizes that the documented print orientation is important for strength. One preserved STL is non-watertight in an independent mesh audit, so inspect and repair the sliced geometry before printing. Compare the shaft and lever direction before choosing a side, use tough cabin-heat-resistant material, and confirm the seat locks and moves through its full range without binding.

Fits S-Class · W126 / C126

Replacement stop for the sunroof-motor clutch adjustment on a 126-series car. The creator designed it after the missing part allowed the roof to drift out of adjustment and states that the part should work directly from the printer. Use cabin-heat-resistant material, compare the original drive version, set the clutch and travel according to service instructions, and verify complete opening, closing and manual emergency operation without binding.

Fits S-Class · W126 / C126

Multi-part replacement for the centre-console ashtray: a storage body plus shallow, flush, blank and outlet-ready plate options. The creator shows the body installed and notes unused space beneath the extended plate for a separately wired 12-volt or USB outlet. Use heat-resistant material, retain safe selector clearance, secure the assembly, and fuse and insulate any electrical addition independently; the files contain no electrical hardware.

Fits W123 Series · W123 / S123 / C123

Replacement heater-control button intended for a two-colour surface indicator. The creator used PLA, 0.08 mm layers, ironing and 100% infill; for automotive cabin use, choose a heat-resistant compatible material and preserve the visible indicator. Compare the shaft interface and confirm the control operates through its full range without binding.

Fits W123 Series · W123 / S123 / C123

Panel and two separate mounting clips for the upper centre console, demonstrated with 300D switch hardware. The creator recommends screws and nuts rather than pop rivets and notes that the face can receive wood veneer. Compare the switch count and opening layout, use cabin-heat-resistant material, keep fasteners and adhesive clear of wiring, and confirm all switches operate freely.

Fits W123 Series · W123 / S123 / C123

Two-cup holder shaped for the centre console and demonstrated by the creator for saloon and estate interiors. The creator printed at 50% infill and fixed the holder with hook-and-loop tape. Use heat-resistant material, secure it without drilling or trapping wiring, keep containers clear of the selector and controls, and verify that it cannot become a loose object under braking.

Fits W123 Series · W123 / S123 / C123

Replacement external button cap carrying the hazard-warning triangle for the dashboard switch identified by the creator as 1238200205. The printable reproduces only the cap, not the complete electrical switch, so that assembly number is not assigned. Use heat-resistant material, retain the original switch mechanism and confirm reliable hazard-light activation, cancellation and indicator visibility before driving.

Fits W123 Series · W123 / S123 / C123

Replacement substrate for the climate-control wood trim, demonstrated on a 1982 300D sedan. The creator warns that control-panel layouts vary between models and instructs users to compare the two rear locating pins and panel shape before printing; a separate wood veneer is required. Restrict use to the matching control layout, keep adhesive away from controls and wiring, and confirm every control moves freely after installation.

Fits W123 Series · W123 / S123 / C123

Replacement rear-deck speaker grille for a Visaton FR 13 speaker. The creator physically tested the FR version; separate FX/PX variants were explicitly untested and are not included. Use cabin-heat-resistant material, secure the speaker independently with appropriate hardware and confirm the grille cannot become loose or interfere with rear visibility.

Fits W123 Series · W123 / S123 / C123

Replacement tailgate clip for the retractable cargo cover on 300 TD/TE estate cars. Fitment is limited to the estate body included in this generation. Compare the mating profile, use cabin-heat-resistant material and confirm the cargo cover latches and releases without loading the tailgate trim. Only the creator's loose-part source photograph is included; the unrelated credited vehicle photograph is retained as evidence but not uploaded.

Fits W123 Series · W123 / S123 / C123

Replacement bezel for the three rotary heater-control knobs. The creator modelled it after all three original bezels on their car had broken, and the source image shows the physical component. Use heat-resistant cabin material, compare the shaft and surrounding control face, and confirm each heater control turns through its full range without rubbing.

Fits W123 Series · W123 / S123 / C123

Two-piece holder and mounting bracket for storing a reflective warning triangle on the inside of the boot lid. The creator measured and photographed this custom installation on a 1979 300 SD that was built for the US market and therefore did not originally have the bracket; no other model year, body, market or factory-option fitment is inferred. The demonstrated installation uses four plastic rivets plus a roughly #10-24 by 1.5-inch screw, nut and wingnut. Compare the boot-lid pressing and triangle dimensions before printing, use automotive-interior heat-resistant material, keep hardware clear of wiring and the outer skin, and confirm the triangle is retained without obstructing the lid or latch.

Fits S-Class · W116

Full-size glovebox body measured by hand from an original 107-series part. The creator states that one hole beside the lamp opening is intentionally absent, so transfer and drill that position from the original only after confirming lamp, latch, hinge and dashboard clearances. Use cabin-heat-resistant material and test the box without forcing aged dashboard trim.

Fits SL · R107

Four-piece printable shell for rebuilding the weathered electrical connector on a 107-series central-locking mechanism cable. The source photographs the failed original, loose terminals, printed assembly and installed connector, and notes that PLA worked for the prototype; PETG, ABS or nylon is preferable for cabin and door-cavity heat. Preserve terminal positions and insulation, disconnect the battery before electrical work, verify polarity and strain relief, and test locking operation before closing the trim.

Fits SL · R107

Cosmetic snap-on cover for an exposed armrest fastener. The source identifies 107-series fitment but gives no production-break or upholstery-colour claim. Use a cabin-heat-resistant material, compare the fastener head and receiving recess, and test gently so the printed clip does not damage aged seat or armrest trim.

Fits SL · R107

Replacement retaining clip for the removable suncover on the 300 SL. The source claims only 300 SL 107-series fitment, so no other engine, trim or model-year application is inferred. Use cabin-heat-resistant material, compare the original clip and mounting interface, and verify secure retention without stressing the cover.

Fits SL · R107

Drop-in cup holder designed for the centre-console recess of the creator's 1989 560 SL. It prints without supports and includes a shallow adjacent tray. Fitment is limited to the demonstrated late-production console; compare the recess before printing, keep the holder clear of the selector and handbrake, and verify that containers cannot interfere with any control.

Fits SL · R107

Four-piece conversion set for the early dashboard centre stack: a single-DIN HVAC/radio panel, left and right slider trim, and an ashtray-replacement holder for a USB charger or voltmeter. The creator built and photographed it in an early 450 SL and warns that switch layouts changed over production even though the panel outline may remain similar. Restrict use to the demonstrated early layout, compare every opening and fastener before printing, fuse any added electrical outlet correctly, and retain safe clearance from wiring and HVAC controls.

Fits SL · R107

Replacement retaining clip for the cabin sun visor. The creator made and printed it for an older 107-series SL and notes that print cleanup may be needed. Use a cabin-heat-resistant material, compare the screw spacing and visor-rod interface with the original, clean the retention opening carefully, and confirm that the visor locks and releases without damaging the headliner.

Fits SL · R107

Replacement internal louver for the centre dashboard vent, with a dashboard-location diagram and CAD view. The creator reports using it to restore broken, non-adjustable air diverters. Match the original orientation, use cabin-heat-resistant material and verify smooth adjustment without binding.

Fits Z4 · E85 / E86

Push-fit single- and double-container holders for the small rear-console recess behind the handbrake. The creator designed and printed them for a 2004 Roadster, including a 473 ml can version. Confirm handbrake, shifter, seat, belt-buckle and roof-control clearance and remove the holder if it can interfere.

Fits Z4 · E85 / E86

Replacement black screw cover for the centre console, shown installed and as loose physical prints. RealOEM and BMWFans identify the compatible separately serviced black plug as 51167906699, produced from April 2005 and used on E85 Roadster and E86 Coupe interiors. Confirm the black trim specification and opening shape before fitting.

Fits Z4 · E85 / E86

Replacement swivelling support arm for a broken dashboard cupholder, shown in the opened installed assembly and beside the original mechanism. Mirror the model for the opposite side. Verify smooth deployment, positive stowage and secure cup support without obstructing the vent or passenger airbag area.

Fits Z4 · E85 / E86

Three-part left/right-mirrored mount set for storing the removable Roadster wind deflector behind the seats, shown installed in four physical views. The design uses four M3 nuts, M3x12 screws, spacers and nut holders. Confirm fastener retention and seat, belt, roof and rear-view clearance.

Fits Z4 · E85 / E86