Find your next part.

Trunk-wall relocation mount for the Roadster folding-top hydraulic motor. The creator and beta testers report over a year of successful use when secured with two zip ties; the relevant physical motor-and-mount image and CAD views are retained. Mount upright with the reservoir uppermost, fasten to suitable metal, protect hoses and wiring, and cycle the roof while checking leaks, chafe, clearance and emergency operation.

Fits Z4 · E85 / E86

Four-piece mounting set for a creator-built acrylic Roadster wind deflector, physically shown after printing. It uses M8 fasteners and hooks around the roll hoops. Inspect the acrylic edges and fasteners, use locking hardware, and verify seat, belt, roof, rear-view and emergency-egress clearance before driving.

Fits Z4 · E85 / E86

Ashtray-panel replacement for two 52 mm gauges, shown physically installed. Installation requires trimming the original ashtray carrier; confirm gauge depth, wiring, shifter and control clearance, fuse any added electrical circuits and keep all warning lamps and controls visible.

Fits Z4 · E85 / E86

Printed replacement for the four retaining circlips on the Roadster folding-top compartment shelf. The creator reports PETG as strong enough. RealOEM and BMWFans identify the separately serviced circlip as 54317113270, used from September 2002 on E85 Roadsters in LHD and RHD markets. Confirm all four clips retain the shelf without obstructing roof movement.

Fits Z4 · E85 / E86

Replacement housing for the seat-drive mechanism used in both Roadster and Coupe. The creator reports the ABS version has worked for seven years and recommends nylon; STEP geometry is included. Seat removal is required, so isolate the battery, observe restraint-system precautions, and verify travel, locking and fastener torque before driving.

Fits Z3 · E36/7 / E36/8

Removable armrest shown physically installed over the centre console. Confirm handbrake, shifter, belt-buckle and seat-travel clearance and remove it if it can interfere with any control.

Fits Z3 · E36/7 / E36/8

Exact-copy replacement for the upper glovebox latch catch, shown installed. RealOEM and BMWFans identify the separately serviced upper catch as 51161849472 and show it in the glovebox diagram for this generation. Verify the lid latches, releases and sits flush without excessive force.

Fits Z3 · E36/7 / E36/8

Screw-retained sleeve for a broken lower finger on the passenger-seat belt guide in the creator's 2002 car. The installed repair, original damage and break diagrams are documented. It does not replace the belt or anchor; verify smooth belt feed and retraction before driving.

Fits Z3 · E36/7 / E36/8

Custom blank for routing microphone or charging cable through an unused centre-console button opening in the creator's 2002 car, shown installed. Secure and fuse powered wiring, protect cable edges, and keep controls unobstructed.

Fits Z3 · E36/7 / E36/8

Replacement right-side dashboard vent designed to snap into the original opening and reported as an effortless installation. It is the passenger-side vent on LHD cars and driver-side vent on RHD cars. BMWFans identifies the right defroster-nozzle cover as 64228399954 from September 1995. Verify louvre movement, duct sealing and dashboard retention.

Fits Z3 · E36/7 / E36/8

Longer repair guide for the Roadster and M Roadster seatbelt guide, independently remeasured after a shorter design moved in use. The creator reports successful PETG use and shows it installed. This is a trim guide, not a restraint anchor; confirm the belt feeds and retracts freely and never modify the belt or anchor.

Fits Z3 · E36/7 / E36/8

Two-piece cupholder and mounting insert for the rear-console slot behind the handbrake in the creator's 1999 2.5-litre Roadster. The source shows it installed. Bond or fasten the parts securely and confirm handbrake, seat and belt-buckle clearance.

Fits Z3 · E36/7 / E36/8

Wear grommet for the Roadster soft-top tension cable. It replaces only the damaged grommet, not the complete BMW tension-cable assembly 54318400951, so that parent number is deliberately omitted. Inspect the cable and top mechanism, and verify unrestricted roof travel before use.

Fits Z3 · E36/7 / E36/8

Two-piece housing and lid for the remote-key receiver when fitting a smaller replacement rear-view mirror with a compatible tri-lobe adapter. The creator reports mounting and using the replacement mirror. Secure the receiver and wiring without obstructing mirror adjustment or visibility.

Fits Z3 · E36/7 / E36/8

Replacement interior door-handle surround shown as a finished physical print from several angles. Test-fit without forcing the trim, confirm the handle returns freely, and use a cabin-heat-resistant material.

Fits Z3 · E36/7 / E36/8

Replacement headlight-switch knob that the creator printed and used after the original disintegrated. The knob body was measured from the original but the decorative cap profile was reconstructed without an original cap, so no BMW component number is assigned. It requires an M5-0.8 nut; verify positive switch operation and retention before driving.

Fits Z3 · E36/7 / E36/8

Plain and USB alternatives for the wider centre-console accessory slot. The creator reports correct fit. BMWFans identifies original cover 51162492136 from January 1997 with this generation in its applications. Dry-fit the chosen insert and secure any connector and wiring before use.

Fits Z3 · E36/7 / E36/8

Plain and microphone-opening alternatives for the dashboard switch opening. The creator reports that the cover fits correctly. BMWFans and RealOEM identify the plain cover as 51168104346 and include this generation in its applications. Confirm microphone retention and keep wiring clear of HVAC and control mechanisms.

Fits Z3 · E36/7 / E36/8

Two alternatives for the small centre-console accessory opening: a plain blank and a USB insert. The creator reports exact fit on this generation. BMWFans and RealOEM identify the original plain plug as 51168400712, introduced January 1996; dry-fit before installing any connector and keep wiring fused and clear of controls.

Fits Z3 · E36/7 / E36/8

Replacement guide bushing for the seat-drive screw where worn originals cause seat wobble. The source identifies the problem on this vehicle and shows the worn assembly and printed bushing; four are required per seat. Seat removal and disassembly are required, so isolate the battery, observe restraint-system precautions, and verify full travel and secure locking before driving.

Fits Z3 · E36/7 / E36/8

Dash-cubby mount for the 10.26-inch Carpuride C94 display, physically fitted and tested by the creator in a 2013 X6. This submission includes only the source's tested 2 mm support version; the later 3 mm support variant was not test-fitted and is excluded. Use a heat-resistant cabin-suitable material, confirm the dashboard cubby geometry before printing, and route the display cable without obstructing vents, controls, airbags or driver visibility.

Fits X6 · E71 / E72

Frame and translucent diffuser for adding a slim legroom light along the upper rear seat-back panel. The creator identifies the design for the contemporary X5 and X6, supplies separate frame and diffuser files plus a combined-print alternative, states that both parts were printed in PETG, and shows the assembly physically installed. This is an electrical lighting retrofit rather than a verified replacement for a catalogued BMW component, so no OEM number is assigned. Confirm seat-back trim geometry, wiring, fuse protection, heat clearance and secure retention before use; never route wiring through seat airbag or adjustment paths.

Fits X5 · F15 / F85 · X6 · F16 / F86

Replacement upper carpet-retaining clip for the left luggage-compartment first-aid-kit recess. The creator identifies the design specifically for the second-generation X5, calls for two clips and documents physically printing it in PLA. Because the archived source provides CAD views rather than an installed comparison, verify the prong spacing, panel thickness and secure retention against the surviving clip before use; prefer a heat-resistant automotive material. No OEM number is assigned because the exact serviced clip identity is not established from the source.

Fits X5 · E70

Replacement retaining clip for third-party winter floor mats. The creator designed and physically printed it after the supplied clip broke, and explicitly states it was used for the mats in a BMW X4 G02. Although G20 and G03 are suggested by the source, those fitments are not independently tested and are intentionally not linked. This is not represented as a genuine BMW component and no OEM number is assigned. Use a durable material such as PETG, ABS or nylon, compare the mating profile with the broken mat clip, and confirm that the mat is securely retained without interfering with pedal travel before driving.

Fits X4 · G02 / F98