Find your next part.

Drop-in organizer for the small driver-side lower-dashboard compartment, with dedicated spaces for glasses, two valve-cap tools and a small lamp. The creator physically shows the organizer loose, loaded and installed in an X3 G01; the pictured M-style lettering is optional decorative geometry and is not a BMW trim or color claim. This is an aftermarket organizer rather than the surrounding storage-compartment assembly, so no parent number is assigned. The evidence shows a left-hand-drive layout; confirm LHD/RHD compartment geometry, trim and equipment, use a cabin-heat-resistant material and verify closure and pedal/control clearance.

Fits X3 · G01 / F97

Clip-on honeycomb cover intended to stop small objects entering the open ventilation duct beneath a front seat, physically shown loose and installed by the creator on a 2024 X3 G01. This is an aftermarket guard rather than a reproduction of a separately serviced BMW child component, so no duct or floor parent number is assigned. Creator evidence is limited to model year 2024; confirm seat position, duct profile, side and production configuration, preserve airflow and seat wiring clearance, and use a cabin-heat-resistant material.

Fits X3 · G01 / F97

Drop-in frame for the factory wireless-charging pad that keeps a phone centered while leaving the charging-status LED visible. The creator recreated it on a 2021 X3 G01 for phones up to approximately 75 x 155 mm and reports using it with a device larger than the original iPhone 15-sized insert. This is an aftermarket retainer rather than the cataloged charging tray, so no parent assembly number is assigned. Confirm charging-pad and phone geometry, option equipment, charging alignment, heat, clearance and retention before driving; use PETG, ABS, ASA or another cabin-heat-resistant material.

Fits X3 · G01 / F97

Two-piece mount for a Musway M6 V3 DSP/amplifier, physically shown installed in the left rear cargo-area electronics space. The creator developed it on an X3 G01 LCI with the HiFi sound system and states that it is not compatible with the Harman Kardon system; assembly uses two M3x10 countersunk fasteners, one M6x20 fastener and two factory bolts. This is an aftermarket equipment mount, not a reproduction of a BMW service part, so no parent electronics or trim number is assigned. Confirm G01 LCI body, HiFi rather than Harman Kardon equipment, cable clearance, ventilation, fastening and trim-panel closure before use.

Fits X3 · G01 / F97

Multipart armrest-console tray for a MagSafe charging puck, physically shown installed in an X3 F25 and documented for 2011–2017 vehicles. The source includes original and current-puck top variants plus separate padding pieces; use only the matching top and padding set. This is an aftermarket charging accessory rather than a reproduction of a BMW service part, so no parent tray or telephone-option number is assigned. Use PETG, ABS or ASA for the body and TPU for padding as documented, verify S6NS/S6NW and earlier telephone-option console geometry, cable routing, heat, charging alignment and armrest closure before use.

Fits X3 · F25

Replacement retaining ring for a loose center-console cigarette-lighter socket, supplied with multiple loose, installation and in-use physical views for an X3 E83. BMW catalog socket-mount and illuminated-ring numbers vary by location and production date, and the source does not identify which original child component this geometry reproduces, so no number is assigned. Use a heat-resistant material and verify electrical isolation, secure socket retention and plug clearance before use.

Fits X3 · E83

Replacement cover for a luggage-compartment child-restraint anchor, physically shown installed by the creator in a 2010 X3 E83. BMW catalogs identify the anthracite/black cover as 51473405879, item 12 with three per vehicle; grey 51473418987 and sand-beige 51473418986 are distinct trim variants and are not assigned. Confirm the interior color and VIN, and verify the cover clips securely without obstructing access to the restraint anchor.

Fits X3 · E83

Six-coin organizer sized for the front ashtray insert and physically tested by the creator in an X3 E83. It also retains the plastic cap from the rear lighter socket. This is an aftermarket accessory, so no BMW ashtray or console parent number is assigned. Use a cabin-heat-resistant material, confirm the insert is bonded securely as documented, and verify it does not obstruct the lighter socket or ashtray closure.

Fits X3 · E83

Two-piece storage mount for the portable Flexible Fast Charger documented with the first-generation iX3: a wall plate retained by three 4.5 mm screw holes and a case-side bracket retained by two M4 x 12 fasteners. The creator printed and physically installed the set, and supplies separate watertight STL files. Verify the pictured charger housing and mounting-hole dimensions before printing because portable charger hardware varies by market and revision. Print vertically with four perimeters as documented, use PETG or another durable heat-resistant material, anchor into a suitable wall substrate, and confirm the charger and cable cannot fall, overheat, abrade, or strain electrical connections.

Fits iX3 · G08

Center-console phone mount sized for an ESR Mini Qi2 charger, with a 58.9 mm diameter and 7.5 mm deep puck recess. The creator documents the printed mount installed in the vehicle and supplies both printable STL and editable STEP files. Verify the pictured console, exact charger revision and phone/case clearance before printing; use a heat-resistant material and ensure the charger, cable and phone cannot obstruct the vehicle controls or overheat.

Fits iX · I20

Center-console holder for a Samsung Galaxy Fold that locks into the factory phone-tray opening to resist tipping under acceleration. The creator's source image shows the printed holder installed in the vehicle with the phone open and in use. Verify the pictured console and your phone/case dimensions before printing; use a heat-resistant material and confirm that the holder cannot interfere with the controller, selector, buttons or safe driving visibility.

Fits iX · I20

Press-fit MagSafe phone mount for the factory center-console phone tray. The original creator designed, printed and installed it in an iX, and documents the installed fit with an iPhone 13 Pro Max in an Apple case. The main mount may be used alone for a wide cased phone or with the supplied left and right side guides. Verify the pictured console tray and MagSafe puck dimensions before printing; use a heat-resistant material, preserve access to all controls, and confirm the phone remains secure without obstructing driving controls.

Fits iX · I20

Replacement width-adjustment clip that lets larger modern phones, including phones in protective cases, fit the factory snap-in wireless charger. The creator designed, printed and installed it in a 2019 Roadster and documents removal, installation and the completed fit. Compatibility is limited to cars equipped with the pictured snap-in charger; verify the installed charger and clearances before printing. Use a heat-resistant material, print at the documented 45-degree orientation, and do not allow the phone or charger to obstruct controls or overheat.

Fits i8 · I12 / I15

Center-armrest organizer with a 15 mm vertical phone slot, a 7 mm cable passage, separate cable storage, a general compartment, and a small raised area for keys. The creator shows the physical organizer installed loaded and empty and explicitly identifies compatibility with G22, G23, G26, and i4 interiors. Use ASA, ABS, or another cabin-heat-resistant material as recommended; verify stable seating, phone and cable clearance, and unobstructed armrest movement.

Fits 4 Series · G22 / G23 / G26 / G82 / G83 · i4 · G26

Flexible protective case for the vehicle remote key, with open access to all buttons and the key-ring eye. The creator shows the TPU case fitted to the physical key from both sides and provides useful CAD views of the openings. Print in TPU as specified, confirm every control moves freely and the emergency-key release remains accessible, and verify that the case cannot press buttons unintentionally.

Fits i4 · G26

Large center-console storage bin that replaces the original cupholder after the cupholder and its USB and 12 V connections are removed. The creator scanned the exposed recess, shows the printed bin installed, and includes a separate flexible floor liner. This is a deliberate accessory conversion, not an equivalent reproduction of the powered cupholder assembly, so no cupholder or console parent number is assigned. Use cabin-heat-resistant rigid material for the bin and TPU for the optional liner; disconnect and secure the original electrical connectors safely, preserve the mounting screws, and verify stable installation and full console-cover clearance.

Fits i4 · G26

Cup-position insert shaped for a Hörmann garage-door remote. The creator shows the remote seated in the printed insert in the center console and provides an improved version 1.0 with a deeper pocket and reduced five-degree angle; only that revised model is retained. This is device-specific accessory geometry rather than an original BMW component. Use a cabin-heat-resistant material, confirm the remote and insert remain secure, and verify that neither interferes with the cup positions, console cover, controls, or driving.

Fits i4 · G26

Pair of compact brackets for hanging a JBL BassPro Nano under the rear-seat frame where the optional amplifier is not installed. The creator printed two in PETG at 50% infill, fastened them with the subwoofer's original screws, and shows the installed unit and bracket locations. Confirm the vehicle lacks the conflicting amplifier, protect wiring, use thread-safe fasteners, and verify seat movement, ventilation and secure retention before driving.

Fits i3 · I01

Anti-tip adapter for the source-linked small espresso cup, shaped for the center-console cup position. The creator shows the physical adapter seated in the vehicle and with the matching cup. Print in PETG, ABS or another cabin-heat-resistant material, verify both the cup and console fit, and keep hot liquids securely contained and clear of controls while the vehicle is moving.

Fits i3 · I01

Three-piece key-fob box with a separate insert, bottom and lid, designed to prevent accidental button presses while carried in a pocket. The source shows the complete physical case closed, open and holding the I01 key fob. This is a protective accessory rather than the key housing itself. Check that the fob fits without continuously loading any button and that the lid remains secure during normal carrying.

Fits i3 · I01

Organizer for multiple EV charging cards that plugs into a center-console cup-holder slot. The source shows the physical organizer installed and loaded with cards. This is an accessory rather than a serviced console component. Use PETG, ABS or another cabin-heat-resistant material, confirm a secure cup-slot fit, and keep the cards and organizer clear of adjacent controls and loose-object hazards.

Fits i3 · I01

Removable center-console cover with an integrated opening for an Apple MagSafe puck, remixed from the original storage cover. The source shows the physical cover installed and provides model views of the puck opening and underside support. It fits non-braided-cable pucks directly; braided-cable versions may require a small amount of adhesive. Use cabin-heat-resistant material, secure the puck and cable, and verify charging temperature and clearance.

Fits i3 · I01

Organizer for the small storage compartment below the armrest, with a rigid body, two optional flexible pads and a single-piece multimaterial variant. The source shows the physical pieces and the organizer installed both loaded and empty. Print the body in PETG or another cabin-heat-resistant rigid material and the pads in TPU; verify stable seating and unobstructed access to the adjacent 12 V and USB connections.

Fits i3 · I01

Center-console switch faceplate with an added opening for a retrofitted Dynamic Traction Control button from an i8. The source shows the ASA print installed around the complete switch bank and notes reinforced side clips. This is retrofit trim, not a stock I01 faceplate, so no switch-bank or i8 parent number is assigned. Confirm the retrofit wiring separately, use cabin-heat-resistant material, and verify button travel and clip engagement.

Fits i3 · I01