Find your next part.

REPLACEMENT TRAY FOR USELESS PHONE CADDY watch this to learn how to remove that useless thing NOT MINE VIDEO ALL THE CREDIT TO THAT GENTLEMAN And then replace it wit the tray enjoy Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Can be installed in preexisting holes, no drilling necessary. BOM: 2 x M4x10 screws 1 x M4x50 screw 3 x M4 nuts Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Can holder designed for 55 mm Red Bull cans. It is only suitable for cars without iDrive because it occupies the center-console location normally used by the iDrive controller. The creator reports a print time of 12 hours 3 minutes and dimensions of 74.8 × 135.1 × 72.4 mm. Use cabin-heat-resistant material, dry-fit the part, and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

In my BMW E91 were the Air Vent Levers missing. The original replacements cost a fortune, so i designed some by myself. Print them with PETG or similar. I recommend to print the fork with hinge part. Use the Fork and the Lock File only if you want to print them separately. For the stripe you may want to change the color, so i made it one part for manual color change by a certain height and two parts for MMU printing. You should add a raft under the Leverpart for better bed adhesion on the very small parts lying on the bed. Print them in the provided orientation Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

OBD2-Cover for BMW e90/e91 Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Seat belt hook attachment for BMW E92. Simply attach with a high quality double sided tape. Confirm normal seat, belt and presenter movement and keep the printed part outside the restraint load path.

Fits 3 Series · E90 / E91 / E92 / E93

The cup holders in my 325i are small and work with anything bigger then a 12oz can. I designed this cup holder fit large insulated tumblers like the Yeti. The top 2 pieces need to be glued together. Gorilla glue works well, but any plastic glue should work. I used a hot glue gun to secure the base to the center console of the car. The hot glue works well and can be removed without any damage to your car. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

When I bought my e91 it had no front console cigarette lighter which meant I had to use an after market accessory plugged into the armrest socket. The unit was then wedged between the console and the passenger seat. Less than ideal. This plate fits in the ashtray hole and has a cut-out to accept an after market twin socket adapter which can be commonly found online or in value stores. I desinged this in sketchup and have included the SKP file in case anyone would like to remix it. Happy Printing Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

This is the cap for the positive battery terminal for a BMW E90. It should fit just about any BMW. Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

I broke my bonnet release for my e92 so printed a new one with the BMW logo in it. It is considerably stronger if printed in PETG and it a perfect fit Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

The BMW E92 has under-seat air-con vents which are prone to getting small objects kicked down them by rear seat passengers. Worse, there a small gap between them through which coins and the like can end up under the carpet where they then rattle annoyingly. Getting them out is a real pain an requires the seat, and possibly the speaker under it, to be removed. These simple grills clip over the vents preventing small objects going where they shouldn't. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

This adapter was used to mount a 25mm twweter of u-Dimension EL Comp 6 system into BMW E46 coupe. You need to print an aditional RH version of LH model provided below. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

This tray replaces the rubbery insert in the coin holder trim on the E46. Mine had begun to degrade, looking waxy and crumbling. I printed this from 85A TPU to replace it. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Got tired of the Velcro pads failing constantly, forcing me to adjust the floor mats every damn time I got in the car. This is my solution. Printing: Small part, so go 100% infill @ .2 or smaller Button face down Organic supports on crossmember PETG pref Install: Remove existing Velcro pads. Align floor mats. Eyeball orientation and location of vertical slot through carpet. Large swiss army knife blade is more or less perfect height. Cut a vertical slit through the carpet into corresponding chassis slot. Pass clip through carpet, into retention slot, and use a nickle/quarter to lock the clip into place. vroom vroom. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Replacement ashtray insert with space for a switch that disconnects the E46 always-live cigarette-lighter outlet. The creator documents the physical insert, wiring and installed switch. Use an automotive rated switch and protected wiring, retain correct fuse protection, insulate every terminal and confirm the ashtray closes freely.

Fits 3 Series · E46

These are brackets to mount an oddments tray (part no 51478230573) that is used in sedans instead of CD changer in the trunk. The brackets allow mounting the caddy in touring as well. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Filament: ASA Supports: Yes (As Applicable) Infill: Minimum 15% Brim: Yes (As Applicable) Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Do NOT print it in PLA, it will deform/melt. Printed with supports. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Front-door reduction adapter physically used in an E46 325Ci Coupe to install a 5.25-inch Kicker speaker in the factory 6.5-inch position. The source shows the printed ring, driver assembly and door fitment. Use sealing foam as documented and verify cone, magnet, wiring, window and door-trim clearance before fastening.

Fits 3 Series · E46

This bracket allows to mount the Pioneer GM-D1004 amp in place of the factory amp in the trunk. I used PETG and it works fine. Put some automotive Tesa tape on the metal ears before sliding the bracket to dampen vibrations. If You are missing a mounting screw or nut here are the codes: 07119902932, 61131372033. Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

Print a cheap replacement for OEM E46 sun visor clips. I recommend printing at 100% infill to prevent splitting at layers when installed. I had good success with a 98A TPU filament at 100% infill with supports on. Just give extra support spacing with TPU and use a torch after to lightly clean up any strings. Wouldn't recommend PLA due to the high temperature that the inside of vehicles can see during the summer heat. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Front-door adapter for installing a 165 mm speaker in the E46 Compact, whose factory speaker differs from other E46 bodies. The creator documents the original door, factory speaker, printed adapter and finished installation. Dry-fit before fastening and verify glass, wiring, cone and door-trim clearance through full window travel.

Fits 3 Series · E46

Isofix cover for BMW E46 I was missing one of the isofix covers so I modeled and printed this one. It's not a perfect copy since I added a bit of thickness in some parts to make it stronger. You can see in one of the images the differences between the original and the 3d printed part. For this one the ABS filament is required since the PETG & PLA are not rigid enough. Added a magnetic version, magnet can be glued in place, 20 x 10 x 3 mm magnet size. This alleviates the need to print the part in ABS for strength. Print Settings Printer: TwoTrees Bluer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Filament: Generic ABS Black Notes: Category: Automotive Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

My dog rides shotgun and would always step on the hazard button when getting in and out, or when I left him in the car. I made this button cover to prevent paws from being able to activate the buttons, but still allow a finger to hit them easily. This is a friction fit in my car and doesn't move around at all. I sanded the top surface in the main picture. source openscad file is attached. Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: 0.2mm layer height Infill: 20% Notes: printed upside down Post-Printing I sanded the top surface to make it a matte finish so it doesn't stick out in the car. Category: Automotive Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46