Find your next part.

Adapter for a standard 100 mm rear ceiling speaker in a 1998 E36 318i Touring. The source physically shows the printed ring, speaker and installed assembly. Confirm cone, magnet, wiring and headliner clearance before fastening.

Fits 3 Series · E36

Three-gauge panel for the E36 sunglasses cubby, physically installed after widening the side clips by 2 mm. The uploaded orientation is for RHD; the creator directs LHD cars to mirror the model. Cutting the original cubby is required, so dry-fit the panel and preserve OBC and switch clearance.

Fits 3 Series · E36

Left and right adapters for installing standard 5.25-inch rear speakers in the BMW E36 318ti Compact without cutting the original housings. The source shows the printed adapters, speaker assembly and installed housings. Verify speaker depth, wiring clearance and screw retention.

Fits 3 Series · E36

Two-piece conversion for the factory 1992–1999 E36 cupholder module, flattening and widening the support for modern cans and cups. The creator used the installed insert and documents 318i, 325i, 328i and M3 fitment. Use cabin-heat-resistant material and confirm the module still clips securely.

Fits 3 Series · E36

Replacement release handle for E30 Touring luggage-compartment side covers, physically installed and reported working with the original bent linkage rods. Verify both latches release and re-engage.

Fits 3 Series · E30

Replacement latch striker for E30 Touring luggage-compartment side covers, reproduced from the original and physically shown working. BMWFans confirms latch striker 51471947370.

Fits 3 Series · E30

Replacement front-seat rail nut cap for E30 cars built before September 1985, copied from the original and physically compared. BMWFans confirms covering cap 52101913670.

Fits 3 Series · E30

Bond-on repair for a broken outer lock section on E30 Touring luggage-compartment side panels, physically demonstrated on an iX panel and mirrorable for either outer side. The referenced latch and spring are separate components and are not assigned.

Fits 3 Series · E30

Replacement slotted screw for retaining E30 seat-mechanism covers. The creator printed and tested revision 3.1 with a deeper screwdriver slot. Tighten only enough to retain the trim.

Fits 3 Series · E30

Smooth replacement covers for the MOMO K2006 steering-wheel hub and the separately measured Alpina leather hub, physically printed and fitted on E30. Select the correct file and verify steering-column clearance.

Fits 3 Series · E30

Resin-printable replacement pivot for the E30 convertible top-lock centering mechanism, physically compared with the original. BMWFans identifies the component as covering for centering bolt 54311971255. Verify pivot movement and roof latching before driving.

Fits 3 Series · E30

Plain replacement cover designed for the sunroof motor opening of a 1987 BMW E30 325is and shown physically fitted. Use heat-resistant cabin material and verify screw and headliner clearance.

Fits 3 Series · E30

Replacement adjustment knob for BMW E30 M-Sport seats, physically shown as a finished print. Match the seat shaft and verify secure engagement before use.

Fits 3 Series · E30

Replacement cap for E30 front seat-belt anchorage bolts, copied from the original and physically fitted on stock, sport and Recaro seats. BMWFans confirms covering cap 72111808464. Do not disturb or conceal a loose anchorage bolt.

Fits 3 Series · E30

Replacement cap for the E30 luggage-compartment jack mount, copied from the original and physically installed. BMWFans confirms cover 51711916269.

Fits 3 Series · E30

Replacement side covers for BMW Reverse RDS, non-RDS, Bavaria and Business radios used in E30, E32, E34 and E36. The source shows physical fit and finish; BMWFans confirms covering cap 65126907823.

Fits 3 Series · E30 · 3 Series · E36 · 5 Series · E34 +1

Replacement gear set for BMW E30 MotoMeter odometers, shown against and installed in a physical cluster. Gear numbers in the source are creator labels, not BMW component numbers.

Fits 3 Series · E30

Replacement E30 ignition-lock trim ring reproduced from a broken original and shown fitted. BMWFans identifies ring 32311162057. Confirm steering-column trim version and do not obstruct key or lock-cylinder movement.

Fits 3 Series · E30

Replacement headliner bracket supporting the dome light in an E30 coupe, physically compared with a failed original and installed. It is not claimed for convertible bodies; sedan fitment was not independently established. BMWFans confirms bracket 54121884483.

Fits 3 Series · E30

Inner and outer replacement covers for E30 headrest-post openings. The creator reports they function, though less precisely than the originals. BMWFans identifies the matching inner and outer covers as 52101838969 and 52108191245; verify position before fitting.

Fits 3 Series · E30

Replacement trim cover for exposed E30 seat-rail and seat-belt anchorage nuts. Match the installed fastener size and ensure the cover does not interfere with seat travel or belt hardware.

Fits 3 Series · E30

Replacement electrical connector housing for the classic Alpina vent gauge, designed around BMW 2.8 mm crimp terminals and compared with the original connector. Match terminal locking and pin order to the vehicle wiring before energizing.

Fits 3 Series · E30

Replacement clip for retaining the E30 sunroof cables. The creator reports two years of use without an issue and recommends PETG. Verify cable capture and unrestricted sunroof travel after installation.

Fits 3 Series · E30

Replacement moonroof slider developed and physically tested for a 1981 BMW E21 320is; the creator expects fit on E21 320 models equipped with a moonroof. Uses two M5 nuts instead of heat-set inserts. Confirm roof cassette, slider travel, nut capture and full open/close operation.

Fits 3 Series · E21