Find your next part.

Replacement door-lock knob for BMW E21, E28 and E30, physically shown beside the original hardware and designed to work with the original or matching printable sleeve. The creator's mixed knob/sleeve catalog references are intentionally omitted. Verify pin diameter and retention.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Replacement door-lock knob sleeve for BMW E21, E28 and E30, enlarged slightly for improved fit and physically demonstrated with the matching knob. The creator's two catalog references cover both sleeve and knob; neither is submitted here because public catalogs did not unambiguously map one number to this modified sleeve.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Replacement trim ring or rosette for the manual sunroof handle on BMW E21, E28 and E30. The creator reports original-location fit and identifies BMW trim ring 54121867887, independently listed for E21 by RealOEM/BMWFans. Verify sunroof-handle version before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Two replacement seat-rail grommets tested on a European July 1982 BMW E21 323i. The filenames reproduce the two catalog shapes for BMW 52101807432 and 52208238999. Confirm seat-rail version, market and grommet position before installation.

Fits 3 Series · E21

Replacement upper outer plastic cover for BMW E21 Recaro seats. Mirror the geometry for the opposite side. BMWFans identifies 52101877057 as left and 52101877058 as right across E21 variants; verify seat type, side and mounting points before fitting.

Fits 3 Series · E21

Adapter for fitting most 6.5-inch speakers at the factory 4×6 rear-shelf positions of a 1981 BMW E21 320i without cutting new holes. The creator reports successful physical fit and sound. Check magnet depth, shelf clearance, fastener security and wiring before installation.

Fits 3 Series · E21

Working replacement retaining clip for the manual window crank of a 1982 BMW E21 320i. The creator reports the reinforced full-base iteration stays installed; other E21 crank variants were not claimed. Print solid and verify positive crank retention before use.

Fits 3 Series · E21

Round organizer insert designed specifically for the factory cup holder in BMW F44 2 Series Gran Coupe models. It provides five coin slots, a BIC-lighter pocket, and an open storage compartment. The creator recommends PETG for cabin heat resistance; verify the approximately 80.4 mm outside diameter against the vehicle before printing.

Fits 2 Series · F44 Gran Coupe

Short adapter ring that centers narrow energy-drink cans in the factory cup holder of BMW F45 Active Tourer and F46 Gran Tourer models. The creator physically tested the reduced-height ring and photographed it installed.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Flexible replacement for BMW rubber buffer 51466967605, creator-tested on an i3 and catalogued for F45, E81/E87, F20/F21, I01, and X1 E84. Print in approximately 85A TPU and cut out the temporary support tab after printing. Within the combined E8x generation, documented fitment is E81/E87 only.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 2 Series · F45 / F46 Active / Gran Tourer +2

Organizer tray for the compartment beneath the armrest in right-hand-drive BMW F45 Active Tourer and F46 Gran Tourer models. The source photograph shows the printed tray installed; this fitment is RHD-specific.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Four support-free mounting-base variants that clip into the small center-console storage pocket of BMW F45/F46 models. Includes fixed and rotating plates; rotating versions use an M5 nut and 12–20 mm bolt. Use PETG, ASA, or ABS rather than ordinary PLA.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Replacement hook that retains the cargo cover in position on the BMW F45 2 Series Active Tourer. Creator photographs show the physical hook installed; compare mounting orientation and clearances before fitting.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Replacement linkage between the rear center-console vent thumbwheel and airflow flap on BMW F45/F46 Active Tourer and Gran Tourer, including pre-LCI and LCI. Remove the vent assembly for access, verify linkage orientation, and use a cabin-heat-resistant material.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Cup-holder insert developed and physically used in a 2016 BMW M2 F87 to keep narrow bottles upright. The source shows the printed insert installed beside a bottle. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the bottle remains secure without obstructing nearby controls.

Fits 2 Series · F22 / F23 / F87

Drop-in organizer tray for the deep center-armrest storage compartment of the BMW 1 Series F70 (2024 onward). Dedicated sections hold coins, keys, charging cables, and a French motorway toll tag. The creator's photographs show the printed organizer installed in the armrest and loose for inspection. Use a cabin-temperature-resistant material and confirm that the armrest closes and latches normally without pinching cables.

Fits 1 Series · F70

Custom-fitted charging pad for the center-console storage recess of the BMW 1 Series F70 (2024 onward). The creator shows the finished pad, its underside with the charger electronics, and the completed installation in an F70. It requires an INIU 15 W Qi charger, careful disassembly, and a shortened USB-C lead soldered to the charger PCB. Use a heat-resistant material, have the electrical work performed by a competent person, insulate and strain-relieve all connections, and stop use immediately if the charger or phone overheats.

Fits 1 Series · F70

Adapter that clips around the BMW F20 center ventilation grille and accepts the creator's screw-mounted phone cradle. Multiple source photographs show the current revision installed. Use ASA, ABS, nylon, or another high-temperature material; inspect the clips for cracking and ensure the phone does not obstruct controls, airbag deployment, or driver visibility.

Fits 1 Series · F20 / F21

Two-piece key tray shaped for the BMW F20 and F21 1 Series cup holder. The body and upper tray are bonded after printing, and the creator shows the assembly installed both empty and holding a key. Use a heat-resistant cabin material and verify that the tray remains secure before driving.

Fits 1 Series · F20 / F21

Measured replacement door-lock knob for a BMW F20 1 Series. The creator modeled the original knob directly, printed it, and shows the replacement installed on the door lock pin. Confirm the bore and free lock movement before use.

Fits 1 Series · F20 / F21

Two-piece removable cup holder for early BMW 1 Series door pockets. A separate interference-fit hook supports the holder in the door pocket; the creator sized it for takeaway cups and drinks cans and supplied a physical print photograph. Print in PETG or ABS for cabin heat resistance and confirm retention before driving.

Fits 1 Series · E81 / E82 / E87 / E88

Cup holder developed and physically installed for a first-generation BMW 1 Series interior. The retained files are the latest creator-supplied right- and left-hand supported variants; earlier revisions are preserved in the source archive but are not submitted. Use a heat-resistant cabin material and confirm local clearance before driving.

Fits 1 Series · E81 / E82 / E87 / E88

Replacement actuator plug for the Jeep Commander rear-seat release lever. Without the plug the seat release does not operate; the printable geometry directly replaces the discontinued original component.

Fits Commander · XK / XH

Adapter designed for the rear HVAC outlet in a 2007 Jeep Commander. It accepts 1-1/8-inch bilge/discharge hose to route air toward a rear child seat, and the source documents the installed setup.

Fits Commander · XK / XH