Find your next part.

Two replacement retaining clips that keep the estate rear seatbelts clear while the seat backs are folded. The creator reports accurate fit and warns that PLA deformed in summer cabin heat; use PETG or a more heat-resistant material.

Fits E-Class · W211 / S211

Left and right plastic recesses that retain the metal mounting points for the estate luggage-compartment protection-net roller on the rear-seat backs. The creator reports a snug fit, recommends PETG with build-plate supports, and notes that the 9 mm bracket holes are intentionally tight.

Fits E-Class · W211 / S211

Replacement hinge set for both sun visors, developed from a 2003 car and explicitly stated by the creator for 1998–2004 SLK 230, SLK 320 and SLK 32 AMG models. Source photographs show the visor, original and printed hinges loose, and the completed visor installed. The creator used carbon-fibre HTPLA with 2 mm walls, 30% gyroid infill, supports and post-print annealing. Treat the supplied end-hinge files and combined hinge file as a set, compare every original piece, use tough cabin-heat-resistant material, smooth pivot surfaces and verify each visor holds securely without obstructing vision.

Fits SLK / SLC · R170

Four-piece left/right replacement retainer set for the power-seat switch panels, explicitly designed as a direct replacement for a 1990s S420. The source photographs show the physical panel assemblies and installed retainers. Independent mesh inspection found three of the four preserved STLs non-watertight, so repair and validate the sliced geometry before printing. Compare side and switch-panel version before use, print in a tough cabin-heat-resistant material, retain the original fasteners, and verify that the panel is secure without restricting any seat control or trapping wiring.

Fits S-Class · W140 / C140

Storage bin replacing the obsolete cassette or CD box in the centre console. The source shows the physical bin loose and installed, recommends 0.20 mm layers and 15% infill and suggests a felt lining. The preserved 3MF loads successfully but is non-watertight in an independent mesh audit, so inspect and repair the sliced geometry before printing. The author distributes it under GNU GPL v3; the API represents that licence as Other. Use cabin-heat-resistant material, check console and selector clearances, secure any retained wiring below the opening and ensure stored objects cannot obstruct vehicle controls.

Fits SL · R129

Replacement angle bracket connecting the centre-console panel to the transmission-tunnel covering on earlier cars. The creator copied the broken original, identifies EPC position 44, and states that the original threaded insert and screw are reused. Confirm early-model console geometry, use tough cabin-heat-resistant material, and tighten only enough to retain the trim without cracking the bracket.

Fits 190 Series · W201

Blanking cover for an unused rectangular switch opening in the upper centre dashboard trim. The creator designed and physically fitted it in a 190-series cabin but does not claim other applications. Compare the opening and surrounding veneer before printing, use cabin-heat-resistant material, and verify the cover cannot interfere with the adjacent rear-window-demister switch or air vent.

Fits 190 Series · W201

Tall and short divider variants that create a small pocket in the armrest center-console storage compartment, with direct physical installation evidence. The creator warns that console shapes vary by equipment version and recommends removable adhesive for retention. This is an aftermarket divider rather than a reproduction of the complete BMW storage compartment, so no parent assembly number is assigned. Confirm the console shape and telephone-equipment configuration, use a cabin-heat-resistant material, and verify that the armrest closes and stored items cannot interfere with controls.

Fits X3 · F25

Clip-on cargo hook for the rear load-area rail, physically shown installed and documented by the creator as used reliably for more than a year. The creator directly lists X3 E83, 3 Series E46, X5 E53 and 5 Series E39 compatibility, so all four live generations are linked. This is an accessory rather than a reproduction of a BMW service part. Print in PETG as documented, observe sensible load limits, and confirm it cannot obstruct the rear seat or cargo cover.

Fits 3 Series · E46 · 5 Series · E39 · X3 · E83 +1

Replacement square cover plug for the screw near the door armrest on BMW E65/E66-family door trim. The creator shows both a loose printed/reference comparison and the installed cover in an E65 door, and describes the geometry as an exact OEM-cover copy. The photographed part is the dark-silver trim variant corresponding to BMW 51417025647; verify color, 24 mm square footprint, door position, production date and VIN before printing because black, flannel-grey, beige and other door-trim cap variants also exist. Use cabin-heat-resistant material and test the retaining legs gently before final installation.

Fits 7 Series · E65 / E66 / E67 / E68

Update: Few of those broke using PLA 0.8 width, infill 10-25%. I suggest you print with 3 layers width (or more?). I will do a redesign to fix the weak point from printing prescriptive. This is my design for BMW floor mat holder (E36 E46 E38 E39) . Top part fits nice and works like a charm. I would say it even holds better than original one. As for the washer (bottom one) I haven't got it in real life so I've designed whatever I thought was suitable. Tested with PLA. Lay it down to print upside down. For now tests are held only in V1 version. Version 1: - Design created. Printed with CURA supports Version 2: - Added supports included in file. Gap is 0.15mm - Redesign of top part "head" - Added washer BMW part number (exemplary) 51478116564 51478183027 51478183028 51478183029 51471881521 Only the creator-tested V1 fastener is retained; the untested V2 washer and supported variant are excluded. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

Left/right interior mounting pod for adding tweeters in a BMW E28. The photographed print is installed in the car; the opening is intentionally generic, so select a tweeter that fits or design a separate driver adapter. Confirm mirror-image orientation, trim contour, sight lines and airbag-free mounting location before drilling or fastening.

Fits 5 Series · E28

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

Shift knob designed for e90 but may fit others. Clips on and does not rotate (careful of breakage if you try to twist it!) Fits fine, but is a bit light. Would be a nice print in transparent colors. Difficult to remove without breaking the teeth! (the knob teeth not yours) Please share your makes :) Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Replacement inner translucent rocker for the BMW E36 power-window switch, physically compared with the original switch. The listed 61318365300 identifies the complete switch assembly, not this printed insert, so no OEM number is assigned. Use heat-resistant translucent material and verify return, illumination and anti-pinch operation.

Fits 3 Series · E36

Replacement sliding jaw for E30 and E28 sunroof mechanisms, copied from the original and physically compared. The source provides a load-oriented two-piece print option; BMWFans confirms sliding jaw 54121933550. Verify full sunroof travel before road use.

Fits 3 Series · E30 · 5 Series · E28

Left and right repair tabs for cracked E30 instrument-cluster mounting ears, test-fitted against an intact cluster and documented for screw or adhesive installation. Align the tabs in the dash before removing the damaged originals.

Fits 3 Series · E30

Cup-holder extension designed and physically installed in a BMW F22 2 Series to move large 32-ounce cups clear of the dashboard while retaining the original recess as small-item storage. Plain and roundel variants are included. The creator reports good retention with a small shim and uses heat-resistant PETG-CF. Verify fit, cup stability, and clearance from controls before driving.

Fits 2 Series · F22 / F23 / F87

Low-profile 17 mm ball mount developed for the BMW F20 1 Series center-console side panel. The creator attaches it with double-sided automotive foam tape, shows it installed with a phone holder, and reports no problems in use. Print in ASA, ABS, or another cabin-temperature-resistant material and keep the device clear of controls and driver sight lines.

Fits 1 Series · F20 / F21

Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.

Fits Renegade · BU

Press-fit extender for the Jeep Renegade rear luggage-cover support. It increases engagement so the cover does not fall when the opposite side is being hooked in place.

Fits Renegade · BU

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Fits Grand Cherokee · ZJ / ZG

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Fits Wrangler · JK

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Fits CJ · CJ-7 · Wrangler · YJ · Wrangler · TJ