Find your next part.

Replacement beauty cap for M50, M52 and M54 engine-cover fasteners, physically shown on the engine. BMWFans identifies the exact component as cap 11121726089 and confirms E34, E36, E38, E39, E46, E53, E60/E61, E65/E66, E83, E85 and Z3 applications. Use engine-bay-rated material and keep it clear of hot or moving parts.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E34 +8

Two-piece M54 engine air-intake duct physically fitted to the E46. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW intake tube 13717509118 for the matching M54 and M56 applications. Use a heat-resistant engine-bay material and verify air-box sealing, bonnet clearance and freedom from belts and fans.

Fits 3 Series · E46

Streamlined replacement alternator cooling duct modeled from a 3D scan of the original failure-prone part and shaped for support-free printing. The creator printed it in PA12 and reports that PETG has also been tested.

Fits 924 · 924 · 944 · 944

Replacement latch clip for the engine-compartment electrical fuse box, identified by the creator as the exact serviced child. Source photographs compare it with the original and show it retaining the lid. Print in engine-bay-temperature-resistant PETG, ABS or nylon, verify the box and latch version, and confirm the lid seals and remains secured without pinching wiring.

Fits Vito / Viano / V-Class · W639

Replacement access door for the factory-style cabin-filter retrofit opening in the evaporator cover. This version is slightly oversized for an opening cut to the moulded guide line.

Fits Land Cruiser · 100 Series · Lexus LX · 470

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Fits Defender · Td5

Adjustable clutch-pedal stop intended to reduce pedal travel. The creator specifies a 60 mm or 80 mm M10 hex-head bolt and nut, two 20 mm M4 bolts with nuts, four 12 mm washers, threadlocker, and PETG.

Fits 924 · 924 · 944 · 944

Printable replacement cover for the engine-bay relay board. The creator printed it in PLA with supports at 0.2 mm resolution and glued the oversized print after splitting it for a 210 × 210 mm bed.

Fits 914 · 914

Use ABS preferably but it wont get that hot up top where this print is located so anything will work Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Replacement access cover for the oil-drain opening in the engine-compartment underbody screening, physically shown loose and installed by the creator. BMW catalogs identify this child cover as 51757261712, item 5 in the underhood-shield diagram; it is used on X3 F25 and X4 F26 applications, so both live generations are linked. The printed design uses lower U-nuts and hex screws rather than the original fastening method. Print in PETG or a higher-temperature engineering polymer, confirm the panel variant and VIN, and verify secure retention and clearance before driving.

Fits X3 · F25 · X4 · F26

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Fits Defender · Td5

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Replacement oil-sump drain-plug access cover for E46 and Z4 E85/E86 undertrays. The creator corrected the screw-hole location and removed reinforcement that caused the physical print to warp. Use an underbody-rated material and verify screw retention, exhaust clearance and complete undertray seating.

Fits 3 Series · E46 · Z4 · E85 / E86

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Fits 3 Series · E46

Three-piece 12-volt inspection-lamp socket adaptation using standard 4 mm RC bullet connectors, 14 AWG silicone wire, and an M3 x 12 mm fastener.

Fits Series · 1 · Series · 2

Replacement hose connecting the mass airflow sensor to the airbox.

Fits 944 · 944

Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +1

Replacement flexible tether for the E30 OBD-I diagnostic connector cap, approximated from a broken original and physically used by the creator. Print in a flexible, heat-resistant material and verify cap retention.

Fits 3 Series · E30

Replacement only shift damper bushing.

Fits 944 · 944

Two-piece replacement dust cover for the steering-gear input shaft. The creator designed it specifically for the first-generation X5 steering rack and shows the printed cover installed around the shaft without removing the steering assembly. Print in a heat-resistant, tough material, secure the two halves as shown by the source, and verify full steering travel, shaft clearance and attachment security before driving. BMW does not catalog this input-shaft cover as a separately serviced child part, so no OEM number is assigned.

Fits X5 · E53

Battery-retaining spacer reproduced from BMW component 61211350825 for E30, E34, E39 and E46. BMWFans identifies it as spacer 1350825 and confirms those chassis among broader BMW usage. Match battery size, tray slot and hold-down engagement, and do not use it to compensate for an incorrect battery or damaged clamp.

Fits 3 Series · E30 · 3 Series · E46 · 5 Series · E34 +1

Replacement outer fuel-filter clip designed for a 2015 F30 328d and reported by the creator to have remained installed for more than a year. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Fits 3 Series · F30 / F31 / F34 / F80

Service funnel sized for the 19 mm automatic-transmission fill tube on a Grand Cherokee ZJ. Small sealing rings are included in the printed geometry.

Fits Grand Cherokee · ZJ / ZG