Find your next part.

Hands-free funnel that screws into the 37 mm by 3 mm-pitch oil-filler opening on the 1FZ-FE engine, keeping it seated above the rocker-cover baffle.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Temporary reservoir cap for pressure-assisted brake bleeding. Inspect the print, seal, and hose connection carefully and use only low, controlled pressure.

Fits Series · 3

Replacement bushing for the manual gear linkage above the gearbox, intended to reduce excess movement during gear selection. Use a durable, wear-resistant material and verify the linkage joint before fitting.

Fits Freelander · 1

Replacement air intake for a Webasto Thermo Top V fuel-burning heater when the original retaining legs have broken. Print with the legs downward and supports from the build plate.

Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320

Replacement bushing for the manual-transmission shifter reverse-lockout knob in the 1968 Ford Mustang application. The longer, thicker profile replaces worn stock bushings to improve fit, smooth operation, and durability. Nylon is the documented material; verify fit and operation before use.

Fits Mustang · First generation

TPU protective boot that covers the exposed starter-motor terminal area, helping shield the cable terminals from contact and contamination. Intended for Ford Pinto starter-motor fitment for 1970–1980 vehicles; the source describes default-orientation printing without supports. TPU heat resistance was not tested.

Fits Pinto · Pinto

M42 × 1.5 threaded shifter-plug set for sealed storage and transport of Type E/Rocket and Dog Box transmissions. Includes a solid cap option and a gasketed two-piece cap with a separate TPU gasket; the gasketed option helps keep dust, fluids, and gear oil out of the tail housing when the shifter is removed. Verified applications include Ford Pinto 1600/1.6/2.0/2.3, Sierra 1.6/2.0, Cortina Mk III 2.0 and Mk IV/Mk V 1.6 GT/2.0/2.3, Escort RS2000 Mk I/Mk II, Escort RS Mexico Mk II, and Mustang II 2.3.

Fits Cortina · Third generation · Cortina · Fourth generation · Cortina · Fifth generation +5

Replacement shift-lever bushing for the shift tube, supplied as closed and open geometry variants for assembly access. It restores the supported shift mechanism interface across the verified Ford applications represented by the attached generation IDs, including Taurus, Bronco, Explorer, Explorer Sport Trac, Freestar, Aerostar, E-Series, F-Series, Ranger, Expedition, and Windstar model-year ranges.

Fits Aerostar · Aerostar · Bronco · Fifth generation · E-Series · Fourth generation +23

Replacement plastic collar for the reverse-lockout cable on the 4x4 manual-transmission shifter. It engages the lockout mechanism during reverse selection and is dimensioned for the Mk2 Sierra 4x4 application; the recovered listing provides one collar component.

Fits Sierra · Sierra

Engine-bay bracket for mounting the coolant reservoir after removal of the factory fuse-box mounting location on the Nissan S13/180SX/200SX/240SX family. The printed part provides the reservoir support interface; the reservoir and fastening hardware are not included. Use a heat- and weather-resistant material suitable for engine-bay service and verify fit, clearance, and secure retention before operation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Two interchangeable full-size intake adapters for mounting CA18DET or SR20DET mass-airflow sensors to compatible A'PEXi filters. Includes separate SR20 and CA18 adapter geometries and requires a 3 mm O-ring cord assembled into the seal groove; printed parts only, with filter, sensor, O-ring cord, and hardware not included. Fits S13, S14, and S15 applications with the corresponding MAF and filter interfaces; verify sensor variant, sealing, fastener engagement, intake clearance, and engine-bay heat resistance before use.

Fits Nissan Silvia · S13 · Nissan Silvia · S14 · Nissan Silvia · S15

3-inch air-filter adapter for mounting a cone filter to the factory naturally aspirated MAF sensor on the Nissan 300ZX Z32 (1989–2000). The screw-in version has 7 mm holes intended for 6 mm bolts and nuts; the filter, MAF sensor, and mounting hardware are not included. The creator specifies ABS and notes PETG or nylon as suitable alternatives.

Fits Fairlady Z / Nissan Z · Z32

Two protective covers for exposed intake and exhaust ports on an SR20 engine. The intake cover is sized for the S13 SR20 configuration, while the exhaust cover is described as compatible across SR20 generations. The covers protect open engine ports from debris during engine storage or installation and include separate intake and exhaust cover components.

Fits Nissan Silvia · S13

Full-size distributor-cap block-off cover for the Nissan Z31 (1983–1989) engine bay after conversion from distributor ignition to coil packs. The cover closes the distributor-cap opening and includes an integrated recessed Z emblem; the printed component and its mounting features are modeled, while installation hardware and the vehicle are not included. Print in PETG, ABS, or another heat-suitable material and verify fastener engagement, sealing, and engine-bay clearances before use.

Fits Fairlady Z / Nissan Z · Z31

Full-size passenger-side front brake vent for the EUDM/AUSDM Nissan 300ZX Z31. The vented grille directs airflow through four openings toward the front brake area and mounts in the side bodywork ahead of the wheel. The supplied geometry represents the right-hand part; mirror it for the driver side. Verify body-opening dimensions, mounting tabs, side orientation, and brake-clearance before installation.

Fits Fairlady Z / Nissan Z · Z31

Full-size radiator support mounting bracket for Nissan Silvia S13 and 180SX RS13/RPS13 applications, with the source also identifying 200SX and 240SX market variants. The bracket mounts at the front radiator support and retains the radiator with the corresponding vehicle hardware. Includes one printed bracket; verify exact market/body variant, hole spacing, fasteners, clearances, and engine-bay heat and vibration suitability before installation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Four-piece set of replacement holders for routing and retaining underbody fuel lines on Nissan 180SX RS13/RPS13 and Nissan Silvia S13 applications. The selected OEM-replacement variant includes Halter 1 E, Halter 2 E, Halter 3 E, and Halter 4 E; print duplicates as needed for the vehicle's layout. This variant retains the fuel lines and the original evap/fuel-tank venting line. Verify line routing, fastener fit, clearance, and print strength on the specific vehicle before installation.

Fits Nissan 180SX · RS13/RPS13 · Nissan Silvia · S13

Replacement battery hold-down bracket for the 1969-1978 Fairlady Z / Datsun Z S30 application represented by 240Z, 260Z, and Fairlady Z fitments. It uses the stock firewall bolt hole and standard battery-tray tie-down rod to secure a smaller or lower battery. Includes one printed bracket; the battery, tie-down rod, fasteners, and tray are not included. Creator guidance specifies Nylon and notes that PETG or another higher-temperature filament may also be suitable for engine-bay temperatures; supports are required for the long battery-contact area.

Fits Fairlady Z / Datsun Z · S30

Full-size adapter for mounting an HKS SQV 4 blow-off valve to the factory recirculation plumbing, returning discharged air to the intake system. Verified fitment is the fourth-generation Subaru Legacy BL/BP (2003-2009) with the compatible valve and flange arrangement. Intended for engine-bay service; print in ABS, ASA, or PA-6 CF and verify gasket seating, hose routing, clamp retention, and clearances before operation.

Fits Legacy · Fourth generation (BL/BP)

Printed mount for securing a small motorcycle clutch-fluid reservoir in the engine-bay hydraulic-clutch installation of a manual-converted 1991–1996 Subaru Alcyone SVX. The geometry provides the reservoir mounting interface; verify reservoir dimensions, fastener engagement, clearances, fluid compatibility, print strength, and secure retention before operation.

Fits Alcyone SVX · First and only generation (CX)

Firewall sound-generator delete plug that seals the opening left when the intake noise-generator tube is removed. Intended for the first-generation BRZ (ZC6); the cylindrical plug presses into the firewall opening. Print guidance specifies PETG or ASA at 20–30% infill for durability, with supports checked in the slicer.

Fits BRZ · First generation (ZC6)

Replacement battery-cover retaining clip for Volvo P3-platform vehicles. Restores battery-cover retention when the original clip breaks or loses holding strength. Verified fitment includes second-generation XC70, second-generation S80, and first-generation XC60. PETG is recommended for durability and temperature resistance; verify the battery-cover variant, clip engagement, clearances, and secure retention before use.

Fits S80 · Second generation · XC60 · First generation · XC70 · Second generation

Replacement cylindrical bushing for the lower torque-mount/dog-bone assembly on a 2008 Volvo XC90 D5. The part has a central sleeve bore and is intended to replace the worn bushing in the existing mount; verify the sleeve and hardware fit, press fit, dimensions, material hardness, and installation before use.

Fits XC90 · First generation

Flexible TPU rubber mount/bushing for securing an engine cover. The cylindrical insert provides a compliant locating and isolation interface at the engine-cover mounting opening. Fitment covers the live S60 I/II, V70 II/III, S80 I/II, XC70 I/II, XC90 I, C30, C70 II, S40 II, V50 I, V40 II, V60 I, and XC60 I generations listed below; verify engine variant, dimensions, quantity, and retention before installation.

Fits C30 · First and only generation · C70 · Second generation · S40 · Second generation +13