The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
171 matching parts
Free files. Made for your car.
C3D–02183Alternative M6 and M4 adapters for fitting an aftermarket threaded shift knob to the standard shift rod. Use the M6 variant with an intact original thread; the M4 variant requires drilling and tapping a damaged rod. Confirm secure retention, full gear selection and no reverse-lockout interference before driving.
Fits Giulietta · Tipo 940
C3D–02163
C3D–02143Replacement cam gear cover bung plug for hole near distributor.
Fits 944 · 944
C3D–02136
C3D–02135
C3D–02123
C3D–02122Replacement transaxle shifter linkage mod.
Fits 944 · 944
C3D–02061Rear cover for the early control unit.
Fits 924 · 924 · 944 · 944
C3D–02054Rear-side Turbo air-filter-box repair bracket with a captive-nut insert.
Fits 944 · 944
C3D–02053Repair bracket replacing the broken intercooler-pipe support on the Turbo air-filter box.
Fits 944 · 944
C3D–01983Replacement plastic clip for securing the regulator/relay-board wiring harness. The creator modeled it from the unavailable original, specifies ABS, and shows the original beside the printed replacement.
Fits 914 · 914
C3D–01966Plastic clip that holds the fuel rail to the engine-bay firewall, modeled against an original clip.
Fits 914 · 914
C3D–01965Two-piece bracket that mounts a remote clutch bleed-screw assembly to the fan shroud. It is sized for a -3 AN bulkhead mount accepting a 3/8-24 bleeder screw and uses a removable end plate so the clutch line can be slid into place without disconnecting it.
Fits 911 · 993
C3D–01952Three printable shift-linkage repair inserts designed for a 1997 five-speed car. The creator specifies PETG or ABS, no supports, 40% infill and 2 mm walls, and reports positive initial road-test results.
Fits Boxster · 986
C3D–01947Repair bracket for the broken air-filter-box arm that retains the metal band connecting the housing to the turbocharger discharge/intercooler pipe. The printed bracket attaches to the top of the box by hot stapling, plastic welding, or adhesive and uses a small pin for the steel band.
Fits 944 · 944
C3D–01934A 60 mm duct for the auxiliary heater fan, supplied as a single printable model. The creator printed it in ABS and states that PLA should also work.
Fits 914 · 914
C3D–01896Replacement cover for the Bosch idle-control valve sensor used on the 156 and 166. The creator designed it because the original cover is discontinued separately from the complete sensor.
Fits 156 · Tipo 932 · 166 · Tipo 936
C3D–01862Two solid filler blocks for the jack-point air gaps. The creator printed them at 100% infill in ABS as a lower-cost alternative to 0.25-inch and 0.125-inch ABS or Delrin sheet.
Fits 4C · Tipo 960
C3D–01804Flexible replacement tether published specifically for this generation. The creator requires TPU and instructs removal of the lid pin and remaining old tether before fitting the new piece snugly around the fuel cap without affecting its seal. Compare the pin, cap eye, tether length and filler-lid clearance, use fuel-vapour-, UV- and weather-resistant TPU and confirm the tether cannot enter the filler neck or prevent the cap from sealing completely.
Fits C-Class · W204 / S204 / C204
C3D–01783Two-piece replacement housing for the starter cable connector on a 2006 SLK 350. The creator modeled it after the original housing crumbled, printed it successfully in ABS, and warns that its position under the exhaust manifold exposes it to substantial heat. Use both housing halves, print only in a suitable high-temperature electrical-insulating material, inspect the cable and terminal for heat or corrosion damage before installation, maintain factory routing and insulation clearances, and discontinue use immediately if the print softens, cracks, or allows terminal movement. Fitment is source-backed only for the stated 2006 SLK 350 within R171.
Fits SLK / SLC · R171
C3D–01764Flexible replacement tether for the fuel filler cap, created after the original tether failed and shown installed on the filler door. Print in fuel-, UV- and weather-resistant flexible material, preserve the cap sealing surfaces and venting, keep the tether clear of the neck and hinge, and confirm the cap still seals and locks normally.
Fits Vito / Viano / V-Class · W639
C3D–01762Replacement wing nut used on several battery and storage-compartment covers. Source imagery shows the installed fastener location and the loose printed geometry. Match the original thread and cover version, print in tough cabin-heat-resistant material, do not force a mismatched thread, and tighten only enough to retain the non-structural cover without cracking it.
Fits Vito / Viano / V-Class · W639
C3D–01723Protective cap for the exposed upper shock-absorber bolt, shown installed by the creator and printed in PETG to tolerate engine-bay heat. The source gives no suspension variant, bolt dimensions or OEM reference. Compare the bolt and surrounding travel envelope, use engine-bay heat-, fluid- and vibration-resistant material and verify the cap cannot loosen, trap corrosive moisture or interfere with suspension inspection or service.
Fits C-Class · W203 / S203 / CL203
C3D–01712Replacement flexible tether for the fuel-filler cap, published specifically for this generation. The source contains a printable model and CAD source image but no cap revision, material or durability test. Compare both attachment eyes and tether length, print in fuel-vapour-, UV- and weather-resistant flexible material and verify the tether cannot enter the filler neck or prevent complete cap sealing.
Fits C-Class · W203 / S203 / CL203