Find your next part.

This is a nut for the engine cover as seen in the second image. It works for e46 316i,318i and 320i, possibly for other models that have the same nut. Note: you will need an O-ring or rubber washer (⌀10mm) to prevent unscrewing due to the engine vibrations, the original nut has one too. You'll need ABS filament or PET-G, PLA filament will break after a couple of months. Print Settings Printer Brand: Artillery Printer: Artillery Hornet Rafts: Yes Supports: No Resolution: 0.2 Infill: 25 Filament: ABS or PET-G Notes: minimum 3 perimeter for Vertical shells Category: Automotive Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

Mine got lost, so I decided to make one! Print in PETG or other heat resistant filament. BMW (E46 3 Series, E83 X3) Battery Positive Terminal Base B + - Cover Cap (61138371011) Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46 · 7 Series · E38 · Z3 · E36/7 / E36/8

Protective cap for the upper front strut bearing on a BMW E36, physically shown printed and installed in the engine bay. Use engine-bay-rated material and confirm it clears the strut brace, nut and suspension movement.

Fits 3 Series · E36

Replacement holder for the BMW E36 engine-bay inspection lamp, physically printed by the creator. Use ABS, nylon or another engine-bay-rated material, secure the lamp wiring away from heat and moving components, and verify the lamp cannot detach.

Fits 3 Series · E36

Replacement front engine wiring holder for E30 M20 and creator-listed E28/E34 applications, physically compared with the original. BMWFans confirms holder 11141716134. Use ASA, ABS or another engine-bay-rated material and inspect for heat distortion.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Straight and 90-degree two-piece shells for repairing disintegrated 2.5 mm watertight terminals on BMW E30, E36 and E46. The source shows completed physical connectors. Bond with suitable RTV and verify terminal lock, polarity, insulation and sealing.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46

Replacement front-strut top dust cover for E30 cars fitted with Koni adjustable dampers where the stock cover does not fit. The creator printed and used the PETG version; confirm adjuster clearance and cap retention.

Fits 3 Series · E30

Replacement E30 front-strut wiring holder copied from the original and physically installed. BMWFans confirms cable holder 61131370421. Use heat- and abrasion-resistant material and verify wire clearance through full steering travel.

Fits 3 Series · E30

Dust cap for replacement-style E30 front strut mounts with an approximately 31.3–32 mm opening, where the original cap no longer fits. Test-print the retaining ring and adjust scale for the measured mount before making the full cap.

Fits 3 Series · E30

Press-on replacement cover for the original BMW E21 fuse box. The creator physically installed the ASA print and notes that the 220 mm model can be split and solvent-welded for smaller printers. Verify clearance, electrical isolation, heat resistance and secure retention.

Fits 3 Series · E21

Dimensioned replacement wiring clip for BMW E21, E28 and E30, physically shown in use. BMWFans identifies the two creator-listed catalog applications as cable clamp 63121364431 and clamp 61131362825. Use heat-resistant material and verify loom diameter and mounting-hole retention.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Replacement cable holder corresponding to BMW 61131267476. The creator notes that ABS prints are less flexible than the original and accept a smaller loom or hose. RealOEM and BMWFans list the holder for E21 among many classic BMW applications; only E21 is linked here because the source does not enumerate chassis.

Fits 3 Series · E21

Two-piece intake opening developed and physically fitted to the airbox of a BMW F20/F21 1 Series. The creator states that it is intended to add intake sound, not power; the cutting profile and finished insert are both included. Keep the factory filter path intact, use an engine-bay-temperature-resistant material, de-burr the airbox opening, and inspect the installation for secure retention and contamination paths before running the engine.

Fits 1 Series · F20 / F21

Flexible replacement firewall grommet for Jeep CJ-5 wiring and control-cable pass-throughs. The source documents the TPU print, original comparison, and physical installation around the routed cables.

Fits CJ · CJ-5

Flexible insulating boot for the disconnected cable end left by a non-invasive Gladiator JT auxiliary-battery delete. The source documents the installed cover after towing use and recommends securing its neck with tape.

Fits Gladiator · JT

Nonconductive bracket for a Warn winch power-interrupt solenoid in the Gladiator JT engine bay. It uses an otherwise unused passenger-side body hole with an M6 rivnut; the creator also reports confirmed fitment from Wrangler JL and JLU owners.

Fits Gladiator · JT · Wrangler · JL

Solid replacement cap for the engine-bay relay cover used on 1984–1996 Cherokee XJ and Comanche MJ vehicles. Use a high-temperature material.

Fits Cherokee / Liberty · XJ · Comanche · MJ

Oval firewall grommet for the 4.0L engine-control harness in 1984–1996 Cherokee XJ and Comanche MJ vehicles. Print in a suitable flexible, heat-resistant material.

Fits Cherokee / Liberty · XJ · Comanche · MJ

Engine-bay bracket for mounting a Garmin PowerSwitch and an adjacent winch relay in a Wrangler JL.

Fits Wrangler · JL

Flexible replacement mounting grommet for the engine appearance cover on approximately 2012–2016 Wrangler JK models.

Fits Wrangler · JK

Large spiked washer that spreads the load of the factory 10 mm heat-shield fastener on a Wrangler JK subframe. The creator specifies solid, high-temperature tough material and used glass-filled nylon; sandwich it under a metal washer.

Fits Wrangler · JK

Factory-style under-hood switch panel for a Wrangler JK fitted with an ARB Twin compressor. Versions with and without a reinforced quick-connect air-chuck opening are included.

Fits Wrangler · JK

Protective cover for the exposed front vacuum pump on a 2016 Wrangler JK after installation of an open aftermarket bumper. Check bumper clearance before use.

Fits Wrangler · JK

Replacement retaining clip for the 2.5-litre airbox. The creator trial-fitted nylon prints on a 1990 vehicle, road-tested them and explicitly identifies the matching Comanche application.

Fits Comanche · MJ · Wrangler · YJ