Find your next part.

Printable lamination mold for fabricating a carbon-fibre intake for 155 hp and 170 hp MiTo T-Jet/MultiAir variants. This is a fabrication tool, not the finished intake. The creator says the completed system was designed and tested to reduce intake temperatures and advises editing the F3D source when a positive or negative mold is required; that editable source is archived. PETG is inferred for mold toughness and moderate resin-process heat.

Fits MiTo · Tipo 955

Workshop driver for installing the front crankshaft seal in an Alfa Romeo 2.0 L Nord engine. Check the driver's seating face against the new seal and use controlled force; it is an installation tool, not an in-service engine component.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop tool for centering piston rings in an 84 mm cylinder bore while checking end gap. The 84 mm size is corroborated for the Alfa Romeo 2000 GTV's 1,962 cc engine; confirm the measured bore before use.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop fixture that mounts to the six-bolt rear crank flange of an Alfa Romeo 2.0 L Nord engine for controlled rotation during assembly. Print in PETG at full infill as the creator recommends; never use it to start or run an engine.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop alignment tool for the pressure plate and clutch on Alfa Romeo Tipo 115 GTV coupes. Verify pilot and hub diameters against the removed clutch before assembly; this is an installation aid, not an in-service vehicle part.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Printable repair and alignment jig for rebuilding broken left- or right-side fog-lamp mounting tabs. The creator identifies Giulia and Stelvio fitment and calls for two-part structural plastic adhesive. This is an alignment aid, not a printable lamp or lens.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Custom front wheel seal installer.

Fits 944 · 944

Custom oil pan gasket tool.

Fits 944 · 944

Custom lug nut well cleaner.

Fits 944 · 944

Template for marking a steel press plate used to remove the rear half of a PDK transmission case.

Fits Cayman · 981

Clip that axially constrains lower-mainshaft components while releasing the linear distance sensor.

Fits Cayman · 981

Temporary S2 engine-service plugs for the spark-plug tunnel, injector port and airflow-sensor hose opening.

Fits 944 · 944

Clutch-alignment tool used on a 1985.5 naturally aspirated car and described by the creator as compatible across the model range.

Fits 944 · 944 · 968 · 968

Adapter between the intake J-boot and an air-hose quick connector for low-pressure vacuum-leak testing.

Fits 944 · 944

Tapered installation tool that expands the PTFE piston seal and centers itself in the counterbore of the differential-lock cylinder piston.

Fits 911 · 964

Gauge for setting the stepped brake-caliper piston face to 20 degrees on standard ATE calipers.

Fits 911 · Original (901/911)

Tool used to measure the fuel-pump actuator-rod stroke. The creator identifies it for VW 25/36 hp and Porsche 356 A/early B engines.

Fits 356 · 356 B (T5/T6)

Tool used to set the fuel-pump diaphragm position during rebuilding before securing the pump top. The creator identifies it for VW 25/36 hp and Porsche 356 A/early B engines.

Fits 356 · 356 B (T5/T6)

Cross-hatched lock-nut socket with a 1/4-inch square drive, designed to disassemble a glove-box lock tumbler.

Fits 914 · 914

Temporary plate that bolts over the cylinder-head intake-manifold mounting face to keep debris out during engine assembly.

Fits 914 · 914

Protective installation cap that covers crankcase through-bolt threads so an O-ring is not sliced while being installed. The creator designed it during a 914-6/911T engine rebuild and revised the shape for improved printing.

Fits 911 · Original (901/911) · 914 · 914

Printable camshaft holding-down tool for early five-chain engines in the Boxster 986 and 911 996. The tool holds the camshafts during cylinder-head-cover removal and reassembly.

Fits 911 · 996 · Boxster · 986

Full-size 15.25-inch template for cutting replacement side-section stone-guard film, modeled for the 997 generation.

Fits 911 · 997

Three-piece installation set for an air-cooled rear main seal: a stock-hardware crankshaft centering guide, a punch that seats the seal flush with the case, and a second punch that seats it 1 mm below flush for a worn crank sealing surface.

Fits 911 · 964 · 911 · 993