Find your next part.

Lidded enclosure for hiding excess wiring from an interior LED kit in the center-console armrest area.

Fits Model Y · First generation

Tray for the 2021 forward center console with the sliding door; the creator distinguishes it from the under-armrest compartment.

Fits Model Y · First generation

Mount for positioning a radar detector above the center screen. V2 increases rear contact area; the creator suggests optional double-sided foam tape and warns that retention is not fully proven and screen damage is possible.

Fits Model Y · First generation

Narrow removal tool for lug-nut caps recessed in Gemini wheels where ordinary pliers do not fit.

Fits Model Y · First generation

Female retainer clip and locking pin for the front mudflaps. The creator specifies horizontal printing with supports, 100% infill, and black PETG.

Fits Model Y · First generation

Two-piece cover for the tow-hitch receiver opening.

Fits Model Y · First generation

Pair of screw-retained hangers for storing umbrellas beneath the rear parcel shelf; designed for approximately 16 mm mounting holes.

Fits Model 3 · First generation

Clip-in under-dash mount for the optional power-liftgate button; it uses an existing trim-clip location and requires no tools or hardware according to the creator.

Fits Model 3 · First generation

Interior radio trim surround created by Nicolas Haberl (231Nici).

Fits A4 · B5

Tight-radius bezel for a double-DIN head unit. The creator made it for a 2006 Super Duty dash swap and explicitly lists the retained Ford applications in the fitment evidence.

Fits Edge · First generation · E-Series · Fourth generation · Expedition · Third generation +10

Sleeve for fitting a 66 mm aftermarket shift knob to the factory gaiter. The source explicitly identifies 2013-2014 fitment and notes that supports leave marks that may benefit from finishing.

Fits Mustang · Fifth generation

Replacement bracket for the front door-jamb push-button switch. The source documents a replica-style file and a twist-lock variant, tested on a 1995 vehicle.

Fits Mustang · Fourth generation

Eight-piece glove-compartment assembly fitted inside the dashboard trinket tray to retain small items.

Fits Roadster · First generation

Center-console holder that retains an iPhone 5 in 2.0 vehicles.

Fits Roadster · First generation

Console-dock adapter that charges and retains an iPhone 5 during driving in 2.x vehicles.

Fits Roadster · First generation

Adapter that replaces the original iPhone dock connector in the 2.5 center-console dock.

Fits Roadster · First generation

Four-piece left/right front mud-guard set remixed for M3 square nuts and M3x10 mm screws. The creator thickened each backplate by 2 mm and reports the set fitted the available wheel-liner gap.

Fits Model 3 · First generation

Flexible replacement spacer for a missing exterior door-handle insert that restores the handle's flush position. The creator specifies TPU, 200°C, 10 mm/s, and 15% infill.

Fits Model 3 · First generation

Two-piece holder that relocates the trailer-hitch electrical plug directly to the tow hook for short cables. The creator specifies M6 and M5 screws, separate car- and hitch-side connectors, and a cable with at least nine wires.

Fits Model 3 · First generation

This is the rear left and right window liner. This requires a larger printer but you can cut it in the slicer and join it afterwards

Fits Defender · 200 Tdi

Multi-piece protective cover for the vehicle's jacking-point opening. The creator designed it as a direct replacement for a missing or damaged factory cover and states that it protects the opening from water, salt, dirt and road debris. Print TLC1, TLC2 and TLC_Clip; glue the body pieces as described and print the clip quantity needed for one cover. Reuse sound original retainers or tested automotive fixing clips. This is a protective trim cover only: remove it as required before lifting, never place a jack or stand on the print, and confirm secure retention after installation.

Fits Tonale · Tipo 965

Replacement forward-collision radar cover with thicker clips and extended coverage intended to reduce water, snow and dirt accumulation. The creator test-fitted it on a late-2018 vehicle. Remove it immediately if any radar or driver-assistance warning appears.

Fits Stelvio · Tipo 949

Clip-on cover that blocks the light gap around the sun-visor retaining point while preserving normal visor operation. The creator explicitly identifies 2018-and-later Alfa Romeo Giulia and Stelvio fitment and recommends PETG, ABS or ASA for summer cabin heat.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Cap for the opening in the sun visor. The source explicitly identifies Alfa Romeo Stelvio fitment. Compare the opening and clip geometry before installation and use a cabin-heat-resistant material.

Fits Stelvio · Tipo 949