Find your next part.

Replacement grommet and retaining catch for the bonnet support rod. The creator recommends weather- and heat-resistant material.

Fits Land Cruiser · 60 Series

Replacement interior-light cover and flexible gasket for fitting a low-cost LED panel in place of the original lamp assembly.

Fits Land Cruiser · 60 Series

Pair of rails for replacing the ashtray with a CB radio or another accessory approximately 115 mm wide.

Fits Land Cruiser · 60 Series

Replacement plastic captive nuts for securing the grille, headlamps and front running lights. The creator recommends weather- and heat-resistant material.

Fits Land Cruiser · 60 Series

Insert for the front compartment of the factory centre console, with two 72 mm cup recesses and a vertical phone slot.

Fits Land Cruiser · 60 Series

Blanking cover for the third-row ashtray opening when the original tray cannot be retained.

Fits Land Cruiser · 80 Series

Middle- and side-vent repair inserts that replace crumbled pivot plates and provide new pins for drilled vent vanes.

Fits Land Cruiser · 80 Series

Rear support bracket for the power-seat threaded drive rod. The creator recommends full infill and notes that the centre bore may need adjustment.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Replacement latch for the fuel-filler door.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Deeper replacement pocket for the opening above the stereo, with a rear cable pass-through.

Fits Land Cruiser · 80 Series

Replacement latch for the storage box between the front seats.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Three cup-holder insert variants for the square centre-console opening, including a larger rounded recess and a version with an accessory slot.

Fits Land Cruiser · 80 Series

Replacement blanking plug for unused rectangular dashboard switch positions.

Fits Land Cruiser · 80 Series

Replacement release lever for the lower tailgate, supplied with editable STEP source. The spline fit may need adjustment for individual printers.

Fits Land Cruiser · 80 Series

Hands-free funnel that screws into the 37 mm by 3 mm-pitch oil-filler opening on the 1FZ-FE engine, keeping it seated above the rocker-cover baffle.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Threaded replacement cap for the power-seat drive screw.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Interference-fit insert for the opening above the radio, with interchangeable mounts for a hands-free microphone and magnetic phone holder. The revised body includes pockets for two 5/16 by 1/8 inch retaining magnets.

Fits Land Cruiser · 80 Series

Three ashtray-replacement panel variants for adding rear-seat USB outlets, including switched and mirrored switched layouts.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Workshop socket for removing and installing the radio-antenna retaining nut.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Panel for installing a USB socket beside the rear-heater switch or in place of the coin holder in the centre console.

Fits Land Cruiser · 80 Series

Factory-style switch-blank panel for a flush-mounted combined USB and 3.5 mm auxiliary extension socket.

Fits Land Cruiser · 80 Series

Workshop socket for adjusting the differential side-bearing nut, modelled for a 1991 vehicle.

Fits Land Cruiser · 80 Series

Bulkhead-mounted holder for a standard 33 cl can, with a recess for an optional 6 mm retaining magnet.

Fits Series · 1 · Series · 2

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3