Find your next part.

Replacement sunroof rail and locking bracket for the P38 electric sliding roof. Related genuine guide assemblies are EXM100360 (RH) and EXM100370 (LH)

Fits Range Rover · P38

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Fits Range Rover · P38

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Fits Range Rover · P38

Replacement door-panel/card retainer stud for the Range Rover P38 and Discovery 2. Corresponds to genuine Land Rover MWC9134

Fits Range Rover · P38

Reinforced replacement bonnet-release lever for a right-hand-drive Range Rover P38. Corresponds to Land Rover FSC10004

Fits Range Rover · P38

Custom replacement for the front ashtray section of a 1999 Range Rover P38 4.0 automatic. Includes a standard cigarette-lighter socket opening, space for additional switches, a 2 mm smaller version for vinyl covering, and separate mounting brackets for printers with smaller beds. The related 1999 front centre-console ashtray assembly is Land Rover FKH100350

Fits Range Rover · P38

Height-setting blocks for calibrating Range Rover P38 electronic air suspension level sensors. Includes front and rear blocks for Access, Low, Standard, and High settings

Fits Range Rover · P38

Replacement protective sleeve for the Range Rover Classic heated rear-window cables, Land Rover part 589818. The source author changed the original round section to a square section and tuned the curvature for fit. PETG or nylon is preferable to brittle PLA. LR3DParts converted the original ASCII STL to binary STL without changing its geometry for upload compatibility.

Fits Range Rover · Classic

Replacement clips for the Range Rover Classic plastic access-panel doors beneath the front seats. Includes a friction-fit version and a version with a retaining lip. Attach with a small Command strip or glue

Fits Range Rover · Classic

Simplified, smaller front bumper corner for the full-size Range Rover Classic 200Tdi. Attaches using the original screw. Confirm side and dimensions against the vehicle before printing.

Fits Range Rover · Classic

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Fits Range Rover · Classic

Interior lamp cover for the full-size Range Rover Classic. Print with supports. Replace the incandescent bulb with an LED before fitting so heat does not deform or melt the printed cover.

Fits Range Rover · Classic

Simplified 78 mm centre hub cap for Range Rover Classic alloy wheels. Prints without supports.

Fits Range Rover · Classic

Dashboard blanking plate for a full-size Range Rover Classic when no car radio is installed.

Fits Range Rover · Classic

Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.

Fits Range Rover · Classic

Replacement fuse-box cover for the full-size Range Rover Classic.

Fits Range Rover · Classic

LandRover Discovery 2 Rear light cover The model provided is for the LEFT side, use the flip/mirror function in your slicer to flip the models for the right side. Can be printed as is, fine details are better. Print in ABS, looks good with some finishing and paint. Helps lights from falling out or getting hit.

Fits Discovery · 2

This is replacement of original LR handle for folding of 3rd row seats in Discovery 2 models.

Fits Discovery · 2

Clip Front Seat Belt Retainer For Land Rover Defender

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Keep snow, ice, and leaves out of your heater intake with this Snow Cowl. The heater intake cover fits Left Hand Drive Defenders (this goes on the Right Hand Wing).

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Simple light guards for Land Rover Defender, just attache them with the original screws.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Originally built to mount a Bolt&Trim Leather speaker holder for the Marshall speaker. This allows for a temporary/movable mount based originally on a cup holder. Could be easily modified for other speaker styles.

Fits Series · 1 · Series · 2 · Series · 2A

A cup holder that clips to the metal dash of a Series 1-2a.

Fits Series · 1 · Series · 2 · Series · 2A

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +8