Find your next part.

Female retainer clip and locking pin for the front mudflaps. The creator specifies horizontal printing with supports, 100% infill, and black PETG.

Fits Model Y · First generation

Two-piece cover for the tow-hitch receiver opening.

Fits Model Y · First generation

Pair of screw-retained hangers for storing umbrellas beneath the rear parcel shelf; designed for approximately 16 mm mounting holes.

Fits Model 3 · First generation

Clip-in under-dash mount for the optional power-liftgate button; it uses an existing trim-clip location and requires no tools or hardware according to the creator.

Fits Model 3 · First generation

Interior radio trim surround created by Nicolas Haberl (231Nici).

Fits A4 · B5

Tight-radius bezel for a double-DIN head unit. The creator made it for a 2006 Super Duty dash swap and explicitly lists the retained Ford applications in the fitment evidence.

Fits Edge · First generation · E-Series · Fourth generation · Expedition · Third generation +10

Sleeve for fitting a 66 mm aftermarket shift knob to the factory gaiter. The source explicitly identifies 2013-2014 fitment and notes that supports leave marks that may benefit from finishing.

Fits Mustang · Fifth generation

Replacement bracket for the front door-jamb push-button switch. The source documents a replica-style file and a twist-lock variant, tested on a 1995 vehicle.

Fits Mustang · Fourth generation

Eight-piece glove-compartment assembly fitted inside the dashboard trinket tray to retain small items.

Fits Roadster · First generation

Center-console holder that retains an iPhone 5 in 2.0 vehicles.

Fits Roadster · First generation

Console-dock adapter that charges and retains an iPhone 5 during driving in 2.x vehicles.

Fits Roadster · First generation

Adapter that replaces the original iPhone dock connector in the 2.5 center-console dock.

Fits Roadster · First generation

Four-piece left/right front mud-guard set remixed for M3 square nuts and M3x10 mm screws. The creator thickened each backplate by 2 mm and reports the set fitted the available wheel-liner gap.

Fits Model 3 · First generation

Flexible replacement spacer for a missing exterior door-handle insert that restores the handle's flush position. The creator specifies TPU, 200°C, 10 mm/s, and 15% infill.

Fits Model 3 · First generation

Two-piece holder that relocates the trailer-hitch electrical plug directly to the tow hook for short cables. The creator specifies M6 and M5 screws, separate car- and hitch-side connectors, and a cable with at least nine wires.

Fits Model 3 · First generation

This is the rear left and right window liner. This requires a larger printer but you can cut it in the slicer and join it afterwards

Fits Defender · 200 Tdi

Multi-piece protective cover for the vehicle's jacking-point opening. The creator designed it as a direct replacement for a missing or damaged factory cover and states that it protects the opening from water, salt, dirt and road debris. Print TLC1, TLC2 and TLC_Clip; glue the body pieces as described and print the clip quantity needed for one cover. Reuse sound original retainers or tested automotive fixing clips. This is a protective trim cover only: remove it as required before lifting, never place a jack or stand on the print, and confirm secure retention after installation.

Fits Tonale · Tipo 965

Replacement forward-collision radar cover with thicker clips and extended coverage intended to reduce water, snow and dirt accumulation. The creator test-fitted it on a late-2018 vehicle. Remove it immediately if any radar or driver-assistance warning appears.

Fits Stelvio · Tipo 949

Clip-on cover that blocks the light gap around the sun-visor retaining point while preserving normal visor operation. The creator explicitly identifies 2018-and-later Alfa Romeo Giulia and Stelvio fitment and recommends PETG, ABS or ASA for summer cabin heat.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Cap for the opening in the sun visor. The source explicitly identifies Alfa Romeo Stelvio fitment. Compare the opening and clip geometry before installation and use a cabin-heat-resistant material.

Fits Stelvio · Tipo 949

Clip-on shield for the original forward-collision radar cover to reduce water, dirt and snow accumulation. The creator explicitly states Alfa Romeo Stelvio and Giulia fitment and reports testing at all sensitivity settings without affecting operation. Remove it immediately if any radar or driver-assistance warning appears.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement left and right deflectors fitted ahead of the rear wheels, with an optional reinforcement pad for a flexible print. The creator reports months of use. Print the deflectors in TPU for flexibility and the reinforcement pad in a stiff weather-resistant material; verify wheel, tyre, suspension and fastener clearance before use.

Fits Stelvio · Tipo 949

Snap-on door-hinge cover designed and test-fitted on a 2018 vehicle. It fits without adhesive according to the creator. Use PETG or another cabin/exterior-heat-resistant material and confirm the cover does not interfere with hinge travel.

Fits Stelvio · Tipo 949

Console-mounted phone holder sized for an iPhone 12 Mini with a protective case. The creator explicitly states Alfa Romeo Stelvio and Giulia fitment and recommends PETG or ABS because cabin heat can deform PLA. Confirm device clearance and secure retention before driving.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949