Find your next part.

Two-hole replacement block for the door area of a classic Spider Duetto. Compare the mounting-hole spacing and installed orientation with the original part before use.

Fits Spider · Series 1 (Tipo 105 / 115)

Replacement flexible cap fitted between the windscreen-wiper arm and retaining nut on 1970s Alfa Romeo Tipo 115 Spiders. Check pivot clearance and secure wiper-arm retention before use.

Fits Spider · Series 2 (Tipo 105 / 115)

Workshop driver for installing the front crankshaft seal in an Alfa Romeo 2.0 L Nord engine. Check the driver's seating face against the new seal and use controlled force; it is an installation tool, not an in-service engine component.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop tool for centering piston rings in an 84 mm cylinder bore while checking end gap. The 84 mm size is corroborated for the Alfa Romeo 2000 GTV's 1,962 cc engine; confirm the measured bore before use.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop fixture that mounts to the six-bolt rear crank flange of an Alfa Romeo 2.0 L Nord engine for controlled rotation during assembly. Print in PETG at full infill as the creator recommends; never use it to start or run an engine.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Workshop alignment tool for the pressure plate and clutch on Alfa Romeo Tipo 115 GTV coupes. Verify pilot and hub diameters against the removed clutch before assembly; this is an installation aid, not an in-service vehicle part.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Two source-provided replacement connector variants for the cabin heater vents in 1970–1976 Alfa Romeo 2000 GTV/unificato Bertone coupes. Compare the original connector and select the matching variant before installation.

Fits Giulia GT / GTA · Tipo 105 / 115 Coupes

Printable repair and alignment jig for rebuilding broken left- or right-side fog-lamp mounting tabs. The creator identifies Giulia and Stelvio fitment and calls for two-part structural plastic adhesive. This is an alignment aid, not a printable lamp or lens.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement cover for a lost or broken ISOFIX access-opening flap on 2018-and-later Giulia and Stelvio rear seats. This is non-structural trim and must not obstruct the child-seat anchor.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Replacement passenger-side trim cover around the seat-adjustment controls. The creator explicitly identifies Giulia and Stelvio fitment; verify switch clearance before use.

Fits Giulia · Tipo 952 · Stelvio · Tipo 949

Longer and less bulky interior-mirror attachment variant for the creator’s Giulia phone-mount system, providing additional adjustment range.

Fits Giulia · Tipo 952

Adapter for mounting a Sony Xperia Z5 Compact at the interior-mirror location. It is the phone-side companion to the creator’s Giulia mirror attachment.

Fits Giulia · Tipo 952

Replacement actuator finger for the glovebox latch. The creator made it for a Giulia Quadrifoglio after the original plastic actuator failed. Check latch release and retention before closing the glovebox.

Fits Giulia · Tipo 952

Clip for 7.5 mm Lumenition Performance high-tension ignition leads used on Alfa Romeo Tipo 105 cars. Confirm lead diameter, avoid sharp bends, and keep the clip clear of hot or moving engine components.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +5

Replacement spacer for the speedometer drive where the cable connects on Alfa Romeo Tipo 105 cars. The creator copied an original spacer, printed it in ASA, and reports successful fit and operation.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +5

Replacement clamp/spacer securing heater-control cables to the heater levers in Alfa Romeo Tipo 105 and 115 cars. The creator printed PETG at full infill and suggests checking shrinkage and lever movement after installation.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +8

Flexible replacement floor bung or blind grommet for 1960s–1970s Alfa Romeo Tipo 105 and 115 vehicles. Print in TPU and verify the opening size and retention before road use.

Fits 1750 / 2000 Berlina · 1750 Berlina (105.48) · 1750 / 2000 Berlina · 2000 Berlina (105.12) · Giulia · Tipo 105 / 115 Berlina +6

Alternative M6 and M4 adapters for fitting an aftermarket threaded shift knob to the standard shift rod. Use the M6 variant with an intact original thread; the M4 variant requires drilling and tapping a damaged rod. Confirm secure retention, full gear selection and no reverse-lockout interference before driving.

Fits Giulietta · Tipo 940

Three attachment joints for bonding inside a right-side aftermarket mirror cap. The creator specifies Alfa Romeo Giulietta fitment and epoxy adhesive. Right side only; dry-fit every joint, prepare bonding surfaces correctly, and verify the cap remains secure.

Fits Giulietta · Tipo 940

Replacement retainer for the 90-degree end of a broken interior door-release cable. The creator redesigned and installed it in a Giulietta door mechanism. Use a tough material and verify reliable repeated release from inside and outside before returning the vehicle to service.

Fits Giulietta · Tipo 940

Storage shelf fitted ahead of the gear lever above the DNA selector area on 2013-on vehicles. The creator shows it installed and reports printing without supports with adequate cooling. Keep the selector and adjacent controls fully accessible.

Fits Giulietta · Tipo 940

Left- and right-side spacers that provide clearance for protruding LED high-beam cooling hardware while retaining the original rear headlamp covers. The creator requires silicone sealing. Use heat- and weather-resistant material and verify both covers remain secure and watertight after installation.

Fits Giulietta · Tipo 940

Press-fit holder for a slim beverage can in the center console. The creator designed and physically fit-tested it in a 2018 vehicle. Confirm stable retention and keep the container clear of the handbrake and controls.

Fits Giulietta · Tipo 940

Reinforced replacement for a weak interior pull handle reverse-engineered from the original component. Use a tough, heat-resistant material, compare the mounting points with the original, and verify the handle is securely retained before use.

Fits Giulietta · Tipo 940