Find your next part.

Phone holder for the shared dashboard cupholder slot; this version fits the 69 mm-wide slot and permits a USB charging connection.

Fits 911 · 996

Tapered installation tool that expands the PTFE piston seal and centers itself in the counterbore of the differential-lock cylinder piston.

Fits 911 · 964

Replacement ramp/clip that pushes down the sunroof wind deflector. The creator fitted the revised design and reported that it works correctly.

Fits 911 · 964

Organizer for the cubby beneath the climate controls, installed by sliding it into the opening from the side.

Fits Macan · XAB Electric

Gauge for setting the stepped brake-caliper piston face to 20 degrees on standard ATE calipers.

Fits 911 · Original (901/911)

Tool used to measure the fuel-pump actuator-rod stroke. The creator identifies it for VW 25/36 hp and Porsche 356 A/early B engines.

Fits 356 · 356 B (T5/T6)

Tool used to set the fuel-pump diaphragm position during rebuilding before securing the pump top. The creator identifies it for VW 25/36 hp and Porsche 356 A/early B engines.

Fits 356 · 356 B (T5/T6)

Center mounting spacer that bridges the different lower profile created by a GT3-style front-bumper conversion and secures the existing front undertray. Its washer section can be retained or removed to adjust the mounting stack.

Fits 911 · 997

Three-part MagSafe phone holder that clips near the glove-box compartment on left-hand-drive interiors. Its position keeps the holder away from the gear lever and leather trim. It accepts a 46 mm-inner/54 mm-outer MagSafe-style magnet ring and the printed parts are joined with super glue.

Fits 911 · 991 · Boxster · 981 · Boxster · 982 (718 Boxster) +2

Extended ball-socket connector for the exterior door-handle linkage, designed to add adjustment when the lever must be pulled too far or is difficult to reconnect. It uses an extra M5 nut; the creator prints it open-slot side up without supports at 0.2 mm layers and about 15% infill.

Fits 924 · 924

Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Fits 911 · 997

Replacement for the upper square CD-case storage unit in the dashboard, with a top cable-routing port for a USB/Bluetooth module. The creator printed it in resin and reports good fit.

Fits 911 · 996 · Boxster · 986

Left and right interior door-handle shells that convert the 997 door release to a GT3-style fabric pull strap. The archive includes a combined pair and strengthened separate left/right versions.

Fits 911 · 997

Threaded plastic ball-socket end for the door-handle drop linkage. The creator says the lower opening must be threaded after printing.

Fits 924 · 924 · 944 · 944

Replacement hanger for a rear-door shade. The creator designed it for the 955/957 and notes that it leaves some visual gaps because it does not perfectly follow the door-trim shape, but remains functional; mirror the model for the opposite side.

Fits Cayenne · E1 (955 / 957)

Drop-in ashtray-delete cubby for the Boxster 986. The creator secured it with double-sided tape and finished it with black flexible interior paint.

Fits Boxster · 986

Cross-hatched lock-nut socket with a 1/4-inch square drive, designed to disassemble a glove-box lock tumbler.

Fits 914 · 914

Adjustable clutch-pedal stop intended to reduce pedal travel. The creator specifies a 60 mm or 80 mm M10 hex-head bolt and nut, two 20 mm M4 bolts with nuts, four 12 mm washers, threadlocker, and PETG.

Fits 924 · 924 · 944 · 944

Cup-holder mount for an Apple MagSafe second-generation 25 W charging puck with braided cable. The creator reports fit with an iPhone 16 Pro Max in a silicone case.

Fits Taycan · J1

Replacement finger plate for an early interior door-release handle, modeled after degraded original trim during an upholstery restoration. The creator printed it in ABS for optional acetone smoothing and says PLA should also work.

Fits 944 · 944

Friction-fit tray variants create a second storage level in the seven-inch-deep center-armrest compartment: plain, tissue-box passthrough, and honeycomb versions, plus a STEP stencil for cutting surface liners. The installed tray sits just above five inches from the bottom, leaving room below for a cube tissue box; the creator had not test-printed the honeycomb variant.

Fits Macan · XAB Electric

Streamlined replacement alternator cooling duct modeled from a 3D scan of the original failure-prone part and shaped for support-free printing. The creator printed it in PA12 and reports that PETG has also been tested.

Fits 924 · 924 · 944 · 944

Left- and right-side frames for fitting nearly any 4x6 speaker behind the factory HiFi grilles while retaining the stock grille appearance.

Fits 911 · 993

Two-piece glove-box CD-holder replacement that mounts two USB ports and provides a pull-out tray for SIM-card access. It assembles with three M3 screws; the updated drawer includes a retaining screw.

Fits 911 · 997